ENGLISH
58
3. Using the hex tool (k) provided, loosen the two
hex bolts (q) at the top of the magazine.
4. Rotate the magazine (g) forward.
5. Remove jammed/bent nail, using pliers if
necessary. Clear out any debris in the nail
channel if required.
6.
If driver blade is in the down position, rotate
the stall release lever (f) on the top of the nailer.
NOTE:
If the driver blade will not reset after
rotating the stall release lever, manually resetting
the blade with a long screwdriver may be
necessary.
7. Rotate the magazine back into position under
the nose of the tool and tighten hex bolts (q).
8. Reinsert battery pack.
NOTE:
The tool will disable itself and not reset
until the battery pack has been removed and
reinserted.
9. Reinsert nails into magazine (refer to
Loading
the Tool
).
10. Release the pusher latch (h).
11. Disengage the trigger safety lock-off (b) when
ready to continute nailing.
If nails become jammed in the nosepiece
frequently, have the tool serviced by an authorised
D
E
WALT service centre.
MAINTENANCE
Your D
E
WALT power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of
serious personal injury, turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories.
An accidental start-up
can cause injury.
The charger and battery pack are not serviceable.
There are no serviceable parts inside.
Lubrication
Your power tool requires no additional lubrication.
NOTICE: NEVER
spray or in any other
way apply lubricants or
cleaning solvents inside
the tool. This can
seriously affect the life
and performance of the tool.
Cleaning
WARNING:
Blow dirt and dust out of
the main housing with dry air as often as
dirt is seen collecting in and around the
air vents. Wear approved eye protection
and approved dust mask when
performing this procedure.
WARNING:
Never use solvents or
other harsh chemicals for cleaning the
non-metallic parts of the tool. These
chemicals may weaken the materials
used in these parts. Use a cloth
dampened only with water and mild
soap. Never let any liquid get inside the
tool; never immerse any part of the tool
into a liquid.
CHARGER CLEANING INSTRUCTIONS
WARNING:
Shock hazard. Disconnect
the charger from the AC outlet before
cleaning. Dirt and grease may be
removed from the exterior of the charger
using a cloth or soft non-metallic brush.
Do not use water or any cleaning
solutions.
Optional Accessories
WARNING:
Since accessories, other
than those offered by D
E
WALT, have
not been tested with this product, use
of such accessories with this tool could
be hazardous. To reduce the risk of
injury, only D
E
WALT recommended
accessories should be used with this
product.
Consult your dealer for further information on the
appropriate accessories.
DCN6901 RETURN SPRING REPLACEMENT KIT (FIG. 8A-8E)
Over time - driver blade return springs will wear
and eventually need replacement. It will become
apparent that the springs will need replacement
when the driver blade does not return home after
Содержание DCN690
