20
EnGLIsh
Mounting the Cutting Cart Assembly to the Saw Frame Assembly
(Fig. E, F, S)
1. Turn the cutting cart stop knob
18
into the unlock position (Refer to
Cutting Cart Stop
Knob
) and slide the cutting cart onto the rails.
Motor Arm Assembly (Fig. A, C, D)
1. Place the water basin
15
on a flat, stable surface, or on the stand.
2. Place saw frame assembly
16
in the water basin
15
.
nOTE:
Make sure the front of the saw frame assembly sits beneath the water basin
bracket
62
to ensure a secure fit (Fig. C).
3. Using the supplied hex key
24
remove the screws
23
from the saw frame assembly.
4. Place motor arm assembly
2
on the saw frame assembly (Fig. D).
5. Secure the saw head by installing two of the screws
23
into the holes closest to the rail.
Tighten the screws with the hex key provided. Install the other four screws in the other four
holes and tighten.
Wrench Storage (Fig. A, B)
Your wet tile saw comes supplied with the two hand tools you will need for assembly. A hex
key
24
and a cutting wheel wrench
25
are stored at the back of the motor arm assembly
2
.
Unpacking the Machine and Its Parts
WARNING:
When moving the machine, always seek assistance. The machine is too heavy
for one person to handle.
1. Remove the loose packaging material from the box.
2. Lift the machine parts out of the box.
3. Remove any remaining packing material from the machine parts.
ASSEMBLY
WARNING:
Prior to assembly always unplug the tool.
WARNING:
When assembling the machine, always follow the instructions in the order as
described below.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal injury, turn tool off and
disconnect tool from power source before making any adjustments or removing/
installing attachments or accessories.
An accidental start-up can cause injury.
Description (Fig. A)
WARNING:
Never modify the power tool or any part of it. Damage or personal injury
could result.
1
On/Off switch
2
Motor arm assembly
3
Plunge handle
4
Head lock knob
5
Cutting disc cover
6
Cutting disc
7
Rubber shroud
8
Small rear water attachment
9
Large rear water attachment
10
Splash guard
11
Cutting cart assembly
12
Small cutting cart water attachment
13
Large cutting cart water attachment
14
Extension table
15
Water basin
16
Saw frame assembly
17
Water nozzles
18
Cutting cart stop
19
Edge guide
20
Cutting wheel cover screw
21
Accessory storage
Intended Use
Your D36000 tile saw has been designed for professional wet tile cutting applications. Using
the appropriate diamond saw blade, diameter 250 mm, it can cut concrete, brick, porcelain
and ceramic materials. Providing optimum versatility, the machine performs the cutting
operations of straight cutting (ripping), diagonal cutting, plunge cutting and bevel cutting
easily, accurately and safely.
This machine is not to be used for any operation other than those mentioned in this manual.
DO nOT
use under wet conditions or in the presence of flammable liquids or gases.
DO nOT
let children come into contact with the tool. Supervision is required when
inexperienced operators use this tool.
•
Young children and the infirm.
This appliance is not intended for use by young children
or infirm persons without supervision.
• This product is not intended for use by persons (including children) suffering from
diminished physical, sensory or mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their safety. Children should never
be left alone with this product.
Labels on tool
The following pictographs are shown on the tool.
Read the instruction manual before use.
Do not use recessed cutting discs.
Wear safety goggles.
Always wear regular working gloves while operating this tool.
Always wear ear protection.
WaRnInG!
Sharp edges.
On/off switch: position I (on) and 0 (off).
Carrying point
Do not place your hands within this area.
80 mm
Maximum depth of cut
Package Contents
The package contains:
1 Motor arm assembly
1 Saw frame assembly
1 Water basin
1 Water pump
1 Cutting disc
1 Cutting cart
1 Extension table
1 Edge guide
2 Rear water attachments
2 Cutting cart water attachments
1 Splash guard
6 Hex screws
1 Hex key
1 Cutting wheel wrench
1 Instruction manual
• Check for damage to the tool, parts or accessories which may have occurred during transport.
• Take the time to thoroughly read and understand this manual prior to operation.
Portable Residual Current Device
The machine is equipped with a portable residual current device (PRCD), which protects the
user against electric shock by interrupting the circuit when a leakage current of 10mA or
greater is detected.
WARNING:
Never operate the machine without the PRCD in place. Do not use the
machine if the PRCD does not function properly. For the PRCD to work, the machine must
be connected to an earthed wall socket. Before using the tile saw, check the function of the
PRCD, pressing the TEST button.
Using an Extension Cable
If an extension cable is required, use an approved 3–core extension cable suitable for the
power input of this tool (see
Technical Data
).The minimum conductor size is 1.5 mm
2
; the
maximum length is 30 m.
When using a cable reel, always unwind the cable completely.
Date Code Position (Fig. A)
The date code
22
, which also includes
the year of manufacture, is printed into the nameplate.
Example:
2020 XX XX
Year and week of Manufacture
25.4 mm
Cutting disc bore
Содержание D36000
Страница 1: ...D36000 ...
Страница 6: ...4 Fig T Fig V Fig X Fig Z Fig Y Fig U Fig W 25 59 58 9 8 13 12 15 19 37 ...
Страница 87: ......
