DeWalt D27111, Оригинальное руководство пользователя

Страница: 41 / 152

39
E N G L I S H
WARNING: Never use solvents or other harsh chemicals for
cleaning the non-metallic parts of the tool. These chemicals
may weaken the materials used in these parts. Use a cloth
dampened only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool into a
liquid.
WARNING: To reduce the risk of injury, regularly clean the
table top.
WARNING: To reduce the risk of injury, regularly clean the
dust collection system
Cleaning and maintaining the kerf plate (fig. U)
Regularly clean the area below the kerf plate.
If the kerf plate is worn it must be replaced.
• Remove the screws (74) holding the kerf plate (8).
• Remove the kerf plate and clean the area below.
• Re-install the parts of the kerf plate and the screws.
• Tighten the screws hand-tight.
• To adjust the kerf plate, proceed as follows:
• Pull down the head until the blade just enters the saw kerf.
• Adjust each part of the kerf plate to fit closely to the teeth of the blade.
• Tighten the screws.
Lubrication
This machine requires no additional lubrication. The bearings of the motor
are pre-lubricated and watertight.
• Avoid using oil or grease as this can cause clogging with sawdust and
chips and create problems.
• Clean the parts subject to accumulation of sawdust and chips
periodically with a dry brush.
Optional Accessories
WARNING: Since accessories, other than those offered by
D
E
WALT, have not been tested with this product, use of such
accessories with this tool could be hazardous. To reduce the
risk of injury, only D
E
WALT, recommended accessories should
be used with this product.
Support for long pieces (fig. A4)
• Always support long pieces.
• For best results, use the extension work support (28) to extend the table
width of your saw (available from your dealer as an option). Support long
workpieces using any convenient means such as saw-horses or similar
devices to keep the ends from dropping.
Dust Collection Port (fig. A5, V)
WARNING! Whenever possible, connect a dust extraction
device designed in accordance with the relevant regulations
regarding dust emission.
• The D27111 will accept the optional dust collection port. For installation,
refer to the dust collection port instructions when purchased.
• The D27112 will accept and is supplied with the dust collection port.
Connect a dust collection device designed in accordance with the relevant
regulations. The air velocity of externally connected systems shall be 20
m/s ±2 m/s. Velocity to be measured in the connection tube at the point of
connection, with the tool connected but not running.
SAW BLADES
ALWAYS USE 305 mm SAW BLADES WITH 30 mm ARBOR HOLES.
SPEED RATING MUST BE AT LEAST 4000 RPM. Never use a smaller
or greater diameter blade. It will not be guarded properly. Use cross cut
blades only. Do not use blades designed for fast ripping, combination
blades or blades with hook angles in excess of 10°.
BLADE DESCRIPTIONS
APPLICATION DIAMETER TEETH
Construction Saw Blades (thin kerf with anti-stick rim)
General Purpose 305 mm 36
Woodworking Saw Blades (provide smooth, clean cuts)
Fine crosscuts 305 mm 60
Consult your dealer for further information on the appropriate accessories.
Protecting the Environment
Separate collection. This product must not be disposed of with
normal household waste.
Should you find one day that your D
E
WALT product needs replacement, or
if it is of no further use to you, do not dispose of it with household waste.
Make this product available for separate collection.
Separate collection of used products and packaging allows
materials to be recycled and used again. Re-use of recycled
materials helps prevent environmental pollution and reduces the
demand for raw materials.
Local regulations may provide for separate collection of electrical products
from the household, at municipal waste sites or by the retailer when you
purchase a new product.
D
E
WALT provides a facility for the collection and recycling of D
E
WALT
products once they have reached the end of their working life. To take
advantage of this service please return your product to any authorised repair
agent who will collect them on our behalf.
You can check the location of your nearest authorised repair agent by
contacting your local D
E
WALT office at the address indicated in this manual.
Alternatively, a list of authorised D
E
WALT repair agents and full details
of our after-sales service and contacts are available on the Internet at:
www.2helpU.com .