background image

9

Never keep the trigger pulled on contact trip tools
when carrying or holding the tool. Death or a serious
puncture wound could occur if the contact trip bumps
something or someone.

Keep your hands and body away from the fastener
discharge area of the tool. Serious personal injury
could occur.

Do not  hold the tool against the work surface with
extra force.  Allow the tool to drive the fastener.

Do not use  the contact trip mechanism as a means of
discharging a fastener because:

1. It could result in personal injury
2. It could result in an accidental release of a

fastener.

3. It may cause damage to the mechanism.
4. It could result in improper placement of fastener

in work piece.

CONTACT TRIP

Your

 

ANF5 Angle Finish Nailer is a contact trip operated

tool.  When the operator depresses the contact trip safety
mechanism against the work surface and then pulls the
trigger, a fastener will be driven.

OPERATING A CONTACT TRIP TOOL:

1.

Requires finger to be off the trigger and the nose of
the tool to be placed on the work surface.

2.

The contact trip safety mechanism is then depressed
against the work surface and the trigger is pulled to
drive a fastener.

3.

The trigger is released after each fastener is driven.

4.

Move the tool to the next  desired fastener  location
and repeat the procedure above.

Check the operation of the contact trip safety
mechanism often.  Do not use the tool if  the
contact trip safety mechanism is not working
correctly.

CHECKING THE OPERATION OF
CONTACT TRIP SAFETY MECHANISM

1. Disconnect the air supply from the tool.

2. Remove all fasteners from the magazine.

3. Make sure the trigger and contact trip safety mechanism

move up and down without any sticking or binding.

4. Reconnect air supply to the tool.

5. Depress the contact trip safety mechanism against the

work surface without pulling the trigger. The tool must
not cycle. Do not  use the tool if a cycle occurs.

6. Hold the tool clear of the work surface. The contact

trip safety mechanism should return to its original
down position. Pull the trigger. The tool 

must not

cycle. Do not use the tool if a cycle occurs.

7. Depress  the contact trip safety mechanism against

the work surface. Pull the trigger. The tool 

must

cycle.

CONTACT  TRIP  SAFETY  MECHANISM

Make sure not to pull the trigger or depress the
contact  trip  safety  mechanism  when  connecting
the tool  to an air compressor. Serious personal
injury can occur if the tool cycles.

Содержание AFN5

















Отзывы: