background image

10 — ENG

Multi-Reg (Low Pressure Setting)

HOW TO SIPHON CHEMICALS/CLEANING
SOLVENTS

Siphoning chemicals or cleaning solvents is a low
pressure operation.

NOTE

Use only soaps and chemicals designed for
pressure washer use.  Do not use bleach.

To siphon chemicals:

1.

Press chemical hose onto barbed fitting located
near high pressure hose connection of pump as
shown.

Barbed
Fitting

Multi-Reg (High Pressure Setting)

RISK OF INJECTION OR INJURY TO
PERSON. DO NOT DIRECT DISCHARGE
STREAM TOWARD PERSONS.

WHEN USING THE HIGH PRESSURE SET-
TING, DO NOT ALLOW THE JET-LIKE
SPRAY TO COME IN CONTACT WITH
UNPROTECTED SKIN, EYES, OR  WITH
ANY PETS OR ANIMALS.  SERIOUS INJURY
CAN OCCUR.

HOW TO USE WAND

Your pressure washer is equipped with a multi-reg
wand with both high and low pressure settings.  The
high pressure setting is for cleaning and rinsing, the
low pressure setting is for applying chemicals or
cleaning solutions to surfaces.

25° fan spray

narrow jet stream

For high pressure operation, pull back the nozzle of
the multi-reg wand as shown.

The nozzle at the end of the multi-reg wand can be
rotated to change the high pressure spray pattern
from a narrow jet to a 25

O

 fan shape, as shown.

Markings have been placed on the nozzle to help you
select the spray pattern.

2.

Place other end of chemical hose with filter on it
into container holding chemical/cleaning solution.

3.

Set multi-reg nozzle to low pressure setting, see

How To Use Wand

 paragraph in this section.

4.

After use of chemical, siphon clean water through
chemical hose to rinse it and pump clean. Chemi-
cals which remain in pump can damage it. Dam-
age to pump due to chemicals will not be covered
under warranty.

NOTE

Chemicals and soap will not siphon when
multi-reg nozzle is in the high pressure
position.

OPERATION

For low pressure operation, extend the nozzle of the
multi-reg wand as shown.

Содержание 2225CWH





















Отзывы: