Devantech dS2832 Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 68

background image

dS28

dS28

32

32

User Manual v4.10

Loading the application firmware

If your module does not flash the blue LED three times on power-up, you will need to update

the system firmware and load the application program. These instructions should also be fol-
lowed if you want to update your firmware to the latest version or even revert to an earlier

version.

You need to download the dScript programming environment from here:

http://www.robot-electronics.co.uk/dscript.html

PC requirements

Windows 7 or later, Linux or MAC OS X
USB port to program the module.

The dScript IDE is supplied as a zip file that can be download and unzipped into a temporary

folder, inside the temporary folder will be four folders:
Installation

USBdriver
Examples

Documentation

Go to the Installation directory and click “setup” to install the dScript IDE, if you have already
installed a previous version you will need to uninstall it before installing the new one.
The USBdriver folder contains the USB com port driver for the modules.
Copy the Examples directory to a convenient location on your computer, it contains both

dScript source code examples and associated web pages, one of which is the application
firmware you will need.

In this order:

1. Start from this position:

a. dScript Editor closed down.
b. dS2832 not connected or powered.

2. Power-up the dS2832.

3. Hold down the reset button for a couple of seconds until the red LED comes on. This in-

dicates the module is in boot-loader mode.

4. Connect the USB lead to the PC. If windows wants a driver, point it to the USB driver

folder and install the driver from there.

Copyright

© 2016-2022,

Devantech Ltd.

All rights reserved.

www.robot-electronics.co.uk

57

«
...
55
56
57
58
59
...
»

Содержание dS2832





































































Отзывы:

Нет отзывов

Похожие инструкции для dS2832

Бренд: Biostar Страницы: 61

Бренд: Ublox Страницы: 23

Бренд: MSI Страницы: 61

Бренд: Supero Страницы: 105

Бренд: AOpen Страницы: 8

Бренд: Obdstar Страницы: 46

Бренд: TYAN Страницы: 63

Бренд: ECS Страницы: 70

Бренд: Fastfame Страницы: 41

Бренд: DFI Страницы: 150

Бренд: Acorp Страницы: 54

Бренд: JETWAY Страницы: 46

Бренд: TRU Components Страницы: 4

Бренд: ASROCK Страницы: 61

Бренд: Gigabyte Страницы: 96

Бренд: Ublox Страницы: 20

Бренд: Micrel Страницы: 23

Бренд: TYAN Страницы: 73

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды