Devantech dS2832 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 68

background image

dS28

dS28

32

32

User Manual v4.10

dSx Configuration

Used to configure dSx42 modules connected to the RS485 bus.
dSx42 modules are extension I/O modules that are connected to the RS485 bus (serial port 3).
Up to 16 dSx modules may be added, controlled by the dS2832 as if they are local I/O. The

outputs are mapped to 2 of the 32 relays – real or virtual and the inputs can be accessed in
the range 100-163. dSx modules are powered from the 12v output on the dS2832’s RS485

connector and wired using a separate pair in the cable. A 2 pair cable is therefore required.
The dSx modules use very little current (less than 7mA each) and 15 of them are easily pow-

ered at the far end of 100 meters of cheap cable. Maximum distance is 305 meters (1000 ft).

Configuration

dSx mode is enable by checking the Enable dSx box. This will configure serial port 3, the
RS485 port, to 250k baud as used by the dSx modules. If un-checked the port will be config-

ured to the Modbus settings on the TCP/IP page. Reset the board after checking or un-check-
ing this box.
To automatically search for dSx modules on the RS485 bus click the Start button. This will
clear all previous devices and mappings and fill the list with all devices found and offer a de-

fault mapping.

Copyright

© 2016-2022,

Devantech Ltd.

All rights reserved.

www.robot-electronics.co.uk

22

«
...
20
21
22
23
24
...
»

Содержание dS2832





































































Отзывы:

Нет отзывов

Похожие инструкции для dS2832

Бренд: Panasonic Страницы: 26

Бренд: Garelick Страницы: 3

ATmega328P Xplained Mini

Бренд: Microchip Technology Страницы: 26

Бренд: Supermicro Страницы: 2

Бренд: MSI Страницы: 92

Бренд: National Semiconductor Страницы: 22

Бренд: ON Semiconductor Страницы: 20

Бренд: Avalue Technology Страницы: 82

Бренд: Supermicro Страницы: 256

Бренд: IEI Technology Страницы: 162

Бренд: Freetech Страницы: 48

Бренд: Yamaha Страницы: 114

Бренд: ALi Confidential Страницы: 24

GENE-9455 Rev.B

Бренд: Aaeon Страницы: 64

EVAL-AD2428WD1BZ

Бренд: Analog Devices Страницы: 6

Бренд: ASROCK Страницы: 98

Бренд: AOpen Страницы: 8

Бренд: Texas Instruments Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды