Dettson GREE E Series Скачать руководство пользователя страница 102

Страница: 102 / 109

Air-to-water Heat Pump Split Versati

SPLIT TYPE

◆

IPM or PFC Over-temperature Protection(Code:"P8")

Is the IPM or

PFC module of

the driver board AP4

tightened?

Replace the

driver board AP4

“Overtemp.-mod.” is

displayed on the wired

controller

P8 is displayed in the

mainboard 88

Indicating Lamp

Work Normally

Tighten the IPM or

PFC module

◆

DC Busbar Over-voltage Protection(Code:"PH") ; DC Busbar Under-voltage Protection (Code:"PL")

Is input voltage ranged

from 185VAC to 264VAC?

Replace the driver board AP4

“DC over-vol.” or “DC

under-vol.” is displayed

on the wired controller

PH or PL is displayed

in the mainboard 88

Indicating Lamp

Work Normally

Please cut off

the power and notify

the power company.

Replace the

driver board AP4.

Does it work normally?

Note: three-phase input voltage is in the range from 320VAC to 475VAC.

Содержание GREE E Series














































































































Результаты поиска

Содержание GREE E Series

Отзывы:

Бренды по названию

Популярные бренды

Dettson GREE E Series, Руководство по обслуживанию

Результаты поиска

Содержание GREE E Series

Отзывы:

Бренды по названию

Популярные бренды