Detroit Radiant Products LD3-15-40 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 60

Detroit Radiant Products LD3-15-40 Скачать руководство пользователя страница 25

25

LD3

Series

3.0

Installation

•

General Venting Requirements

Figure 3.17

•

General Venting Requirements

*Consult the NFPA ANSI Z223.1 Gas Vent Termination criteria if roof pitch exceeds 9:12

24 in.

Min.*

Double-Wall B Vent

Roof*

Heater

1 in. Minimum Clearance -
Use Attic Insulation Shield
(Field Supplied)

Fire Stop Spacer

#8 Sheet Metal Screws (field supplied)

Adjustable Roof Flashing

Storm Collar

B to C Adapter

Clean Out Tee Fitting

Vent Cap

Clean Out Cap

•  Avoid using more than two 90° directional changes in the venting system.
•  Suspend and secure all horizontal runs at points no greater than 3 feet apart.
•  Vent termination must maintain a minimum distance of 6 feet from any mechanical air supply inlet.
•  Vent must terminate a minimum of 4 feet below, 4 feet horizontally from, or 1 foot above any window

or door that may be opened or gravity air inlet into the building.

• Vent must terminate a minimum of 4 feet above grade level and must extend beyond any

combustible overhang. Vents adjacent to the public walkways must terminate a minimum of 7 feet
above grade level.

• The vent terminal must be installed to prevent any blockage by snow and protect building material

from degradation by flue gases.

•  The vent cap must be a minimum of 6 inches from the sidewall of the building.
•  Vent must be a minimum of 36 inches below or extend beyond any combustible overhang.
•  Consult NFPA ANSI Z223.1 Gas Vent Termination criteria for vents that terminate on a roof pitch that

exceeds 9:12.

•

Canada:

Vents must terminate a minimum of 3 feet from a window or door that may be opened, and

a non-mechanical air supply inlet or combustion air inlet into the building.

«
...
23
24
25
26
27
...
»

Содержание LD3-15-40





























































Отзывы:

Нет отзывов