Detroit Diesel EPA07 MBE 4000 Скачать руководство пользователя

Страница: 131 / 157

EPA07 MBE 4000 OPERATOR'S MANUAL

Problem—The Engine Turns Over Slowly

Cause

Remedy

The batteries are damaged or weak.

Test the batteries. Replace them, if
needed.

The ignition switch is damaged.

Replace the ignition switch.

The battery cables are damaged
and/or corroded

Replace the battery cables.

The starter is damaged and/or worn.

Have an authorized repair facility
replace the starter.

The engine oil does not meet the
correct specifications.

Change the engine oil, using the
correct type of oil.

The transmission fluid does not meet
the correct specifications.

Change the transmission fluid, using
the correct type of fluid.

All information subject to change without notice.

119

DDC-SVC-MAN-0041

Содержание EPA07 MBE 4000





























































































































































Результаты поиска

Содержание EPA07 MBE 4000

Отзывы:

Похожие инструкции для EPA07 MBE 4000

Бренды по названию

Популярные бренды

Detroit Diesel EPA07 MBE 4000, Руководство оператора

Результаты поиска

Содержание EPA07 MBE 4000

Отзывы:

Похожие инструкции для EPA07 MBE 4000

Бренды по названию

Популярные бренды