Desoutter CVI3 Function, Руководство пользователя, Страница: 29 / 44

Appendix - User info codes_02/2017 - 29 -
Type of
code
Code
no.
Description Resolution procedure
Info 61 ExBC connection conflict 1- 2 ExBC are configured with the same network settings
2- Verify communication ports and IP addresses
Info 100 Cable id invalid param 1- Invalid tool cable parameter, check that the tool cable is Desoutter
certified
2- Contact your Desoutter representative for support
Info 101 Cable id not detected 1- Tool cable communication error, check that the tool cable is Desoutter
certified
2- Contact your Desoutter representative for support
Info 102 Cable id not certif 1- Tool cable authentification error, check that the tool cable is Desoutter
certified
2- Contact your Desoutter representative for support
Info 199 Console activated 1- The serial console is activated.
2- Warning, this console is dedicated only to debug purposes and should
not be used in production
Info 202 Fieldbus lost 1- Fieldbus connection with PLC is lost.
- no heartbeat is received from PLC
- the cable is broken or disconnected
- the PLC is off line or not powered
2- Check the Fieldbus configuration.
Info 204 Tool not validated 1- Tool locked by I/O.
2- Check the I/O settings: the "Tool validation" must be active to unlock the
tool.
Info 205 Torque settings 1-Invalid Torque setting, torque is greater than tool characteristics
2-Check Pset settings with the current tool characteristics
Info 206 Speed settings 1-Invalid speed setting, speed is greater than tool characteristics
2-Check Pset settings with the tool max. speed.
Info 207 Assembly done 1- Assembly Process is done, the tool is locked
2- Select new Assembly Process to unlock the tool
Info 208 Invalid run reverse param 1-Invalid Run reverse setting, torque or speed are greater than tool
characteristics or reverse strategy is not supported
2-Check Pset settings with the current tool characteristics
3-Reduce max number of turns
Info 209 Pset invalid parameters 1 - Software internal error.
2 - Pset is corrupted. Try to transfer it again to the controller.
3 - If the error persists contact your Desoutter representative for support.
Info 210 Invalid Pset selected 1- The Pset currently selected does not match the selectable one in the
Assembly Process.
Info 211 Invalid trigger conf 1- The tool currently connected to the CVI3 is not equipped with the trigger
required by the tool trigger configuration
2- Adjust your tool trigger configuration to the tool connected or change the
tool according to the expected trigger configuration
Info 215 Current calib. err. 1- Current calibration failed.
2- Try once again.
3- If the problem occurs again, contact your Desoutter representative for
support.
Info 224 IGBT too hot 1- Power electronics too warm.
2- Let the controller cool down.
Info 225 Err. angle 1- Tool communication error.
2- Check tool and cable connections. If the problem occurs again, contact
your Desoutter representative for support.
Info 226 Err. torque 1- Tool communication error. Check tool and cable connections.
2- Try once again, if the problem occurs again, contact your Desoutter
representative for support.
Info 234 Fieldbus mismatch 1-The Fieldbus module declared in configuration is not the same that the
one present in controller (e.g. Profibus declared but a Profinet module in
CVI3).
Info 237 Invalid data 1- The Fieldbus mapping has too many items.
Info 238 Invalid address 1- The device address affected to Fieldbus is invalid.
Info 239 Invalid com settings 1- Fieldbus communication settings are invalid
Info 241 CVINet FIFO alarm 1- The CVINet result FIFO has reached alarm threshold, the CVINet
connection has been lost
2- Check the CVI3 Ethernet cable
3- Check CVI3 Ethernet configuration
4- Check if CVINet is running correctly