background image

110150-01A

For more information, visit www.desatech.com

For more information, visit www.desatech.com

8

Figure 6 - Attaching Left
Surround Side Panel

Surround Side

5/16" Screws

Phillips
Screws

2.

Remove log packaging from firebox cavity.

3.

Align holes in left surround side panel with screen mounting
screw holes.  Replace 5/16" screen mounting shoulder screws
removed in step 1 (see Figure 6). Do not tighten. Install Phillips
screws in bottom (see Figure 6). Repeat for right side.

4.

Using Phillips screwdriver, remove four screws attaching brass
louver. Install one Phillips head screw (included with kit) in
each side (see Figure 7).

5.

Align top panel screw holes. Install four Phillips screws, do
not tighten.

6.

For model GS43, align six screw holes in side panels with
holes in top panel (see Figure 9). For model GS38, align two
screw holes in side panels with holes in top panel (see Figure
9). Insert and tighten screws.

7.

Carefully inspect fireplace surround assembly. Make sure each
part fits properly. Firmly tighten all screws installed during
assembly.

 CAUTION: Do not overtighten. Metal can bend,

warp, or break under excessive strain.

8.

Remove three pieces of brass trim from packaging.

9.

Locate four brass screws, two adjusting plates with set screws,
and two shims in the brass hardware packet.

10. Align shim under adjusting plate as shown in Figure 10.

11. Slide one end of adjusting plate/shim in slot of top brass trim

(see Figure 10).

12. Slide other end of adjusting plate/shim in slot on mitered edge

of side brass trim (see Figure 10).

13. While firmly holding edges of brass trim together, tighten both

set screws on the adjusting plate with slotted screwdriver.

14. Repeat for other side.

INSTALLATION

Continued

Figure 7 - Remove Brass
Louver

Brass Louver

Phillips Screws

Top Surround
Panel

Louver
Screw
Holes

Figure 9 - Attaching Side
Panels to Top Panel (GS43
Pictured)

Top Panel

Side Panel

Figure 8 - Attaching Top
Surround Panel

Phillips Screws (4)

Top Brass
Trim

Figure 10 - Assembling Brass Trim

Slot

Side Brass
Trim

Set Screws

Adjusting Plate

Slot

Mitered
Edge

Shim

15. Line up holes in brass trim with holes on side panels of fire-

place surround assembly. Attach with brass-plated screws.

16. Move fireplace insert and surround assembly to masonry fire-

place opening. Make sure fireplace insert and surround assem-
bly fit properly.

INSTALLATION

Installing Surround Kit (GS38 or GS43) (Cont.)
Installing Hood

Figure 11 - Installing Hood to Firebox

INSTALLING HOOD

Install hood to top of firebox as shown in Figure 11. Use 7 Phillips
screws provided.

Screws

Содержание Vanguard VI33NRA

































Отзывы: