Desa SGS3124N страница 18 Скачать руководство пользователя

Страница: 18 / 28

www.desatech.com

107068-01K

OPERATING HEATER

Continued

5. Slightly depress and turn control knob

counterclockwise

to the PILOT

position. Press in control knob for five (5)

seconds (see Figure 21).

Note:

You may be running this heater for

the first time after hooking up to gas sup-

ply. If so, the control knob may need to be

pressed in for 30 seconds or more. This will

allow air to bleed from the gas system.

6. With control knob pressed in, press and

release ignitor button. This will light pi-

lot. The pilot is attached to the burner. If

needed, keep pressing ignitor button until

pilot lights.

Note:

If pilot does not stay lit, contact a

qualified service person or gas supplier for

repairs. Until repairs are made, light pilot

with match. To light pilot with match, see

Manual Lighting Procedure

7. Keep control knob pressed in for 30 seconds

after lighting pilot. After 30 seconds, release

control knob.

Note:

If pilot goes out, repeat steps 3

through 7.

• If control knob does not pop out when

released, contact a qualified service person

or gas supplier for repairs.

8. Slightly depress and turn control knob coun-

terclockwise

to desired heating level.

The burner should light. Set control knob to

any heat level between HI and LO.

CAUTION: Do not operate

heater between PILOT and HI

positions.

VARIABLE CONTROL

OpERATION

The variable control valve can be set to any

heat setting and flame height desired, by simply

turning the control knob until that setting is

attained. Even the lowest setting provides re-

alistic, dancing yellow flames. Selecting higher

settings produces greater heat output. This

results in increased heating comfort.

CAUTION: Do not try to ad-

just heating levels by using the

equipment shutoff valve.

TO TURN GAS OFF

TO AppLIANCE

Shutting Off Heater

1. Press in and turn control knob clockwise

to the HI position.

2. Turn control knob clockwise

to the

pilot position.

3. Press in control knob and turn clockwise

to the OFF position.

Shutting Off Burners Only (pilot stays lit)

1. Turn control knob clockwise

to the

HI position.

2. Press in and turn control knob clockwise

to the pilot position.

MANUAL LIGHTING

pROCEDURE

1. Follow steps 1 through 5 under

Lighting

Instructions

, starting on page 17.

2. Depress control knob and light pilot with

match.

3. Keep control knob pressed in for 30 seconds

after lighting pilot. After 30 seconds, release

control knob. Now follow step 8 under

Lighting Instructions

, column 1.

Figure 22 - Pilot

Figure 21 - Control Knob and Ignitor

Button Location

Thermocouple

Ignitor
Electrode

Pilot Burner

Ignitor
Electrode

Pilot
Burner

Propane/LP

Natural Gas

Control Knob

Ignitor Button

Thermocouple

Содержание SGS3124N





























Результаты поиска

Содержание SGS3124N

Отзывы:

Похожие инструкции для SGS3124N

Бренды по названию

Популярные бренды

Desa SGS3124N, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание SGS3124N

Отзывы:

Похожие инструкции для SGS3124N

Бренды по названию

Популярные бренды