manualshive.com logo in svg

Desa SGS3124N, Руководство владельца по эксплуатации и установке, Страница: 5 / 28

Поделиться
Скачать
Desa SGS3124N Скачать руководство пользователя страница 5

www.desatech.com

107068-01K

5

PRODUCT 

IDENTIFICATION

Figure 1 - Yellow Flame Vent-Free Gas 

Log Heater Shown (Logs May Vary by 

Model)

Front 
Log

Control Knob

Back Log

Burner

Piezo 
Ignitor

Crossover 
Log 

UNPACKING

 CAUTION: Do not remove the 

data  plates  from  the  grate  as-

sembly. The data plates contain 

important  warranty  and  safety 

information.

1.  Remove logs and heater base assembly from 

carton. 

Note:

 Do not pick up heater base as

-

sembly by burners. This could damage heater. 

Always handle base assembly by grate. 

2.  Remove all protective packaging applied to 

logs and heater for shipment.

3.  Check all items for any shipping damage. If 

damaged, promptly inform dealer where you 

bought heater.

PRODUCT FEATURES

OpERATION

This heater is clean burning. It requires no outside 

venting. There is no heat loss out a vent or up a 

chimney. Heat is generated by realistic, dancing 

yellow flames. This heater is designed for vent-free 

operation with flue damper closed. It has been 

tested and approved to ANSI Z21.11.2 standard 

for unvented heaters. State and local codes in 

some areas prohibit the use of vent-free heaters. 

Non-thermostat models may also be operated as 

a vented decorative (ANSI Z21.60) product by 

opening flue damper.

SAFETY pILOT

This heater has a pilot with an Oxygen Deple

-

tion Sensing (ODS) safety shutoff system. The 

ODS/pilot is a required feature for vent-free room 

heaters. The ODS/pilot shuts off the heater if there 

is not enough fresh air.

pIEzO IGNITION SYSTEM

This heater has a piezo ignitor. This system re

-

quires no matches, batteries or other sources to 

light heater.

AIR FOR COMbUSTION 

AND VENTILATION

 WARNING: This heater shall 

not  be  installed  in  a  confined 

space  or  unusually  tight  con-

struction unless provisions are 

provided for adequate combus-

tion and ventilation air. Read the 

following instructions to insure 

proper  fresh  air  for  this  and 

other  fuel-burning  appliances 

in your home. 

Today’s homes are built more energy efficient 

than ever. New materials, increased insulation and 

new construction methods help reduce heat loss 

in homes. Home owners weather strip and caulk 

around windows and doors to keep the cold air out 

and the warm air in. During heating months, home 

owners want their homes as airtight as possible.

While it is good to make your home energy efficient, 

your home needs to breathe. Fresh air must enter 

your home. All fuel-burning appliances need fresh 

air for proper combustion and ventilation.

Exhaust fans, fireplaces, clothes dryers and fuel 

burning appliances draw air from the house to 

operate. You must provide adequate fresh air for 

these appliances. This will insure proper venting 

of vented fuel-burning appliances.

Содержание SGS3124N





























Отзывы:

Нет отзывов