background image

8

105568

BLUE FLAME NATURAL GAS HEATER

Attaching Mounting Bracket To
Wall

Note:

 Wall anchors, mounting screws, and

spacers are in hardware package. The hard-
ware package is provided with heater.

Models FA-30BB, FAS-30BB, and

FGH-30NGB

Models FA-20BB and FAS-20BB

Figure 7 - Mounting Bracket Clearances

Figure 8 - Folding Anchor

 WARNING: Maintain minimum

clearances shown in Figure 7. If
you can, provide greater clear-
ances from floor and joining wall.

Figure 6 - Removing Front Panel Of Heater

Methods For Attaching
Mounting Bracket To Wall

Only use last hole on each end of mounting
bracket to attach bracket to wall. These two
holes are 16 inches apart from their centers.
Attach mounting bracket to wall in one of
two ways:

1.

Attaching to wall stud

2.

Attaching to wall anchor

Attaching To Wall Stud

This method provides the strongest hold.
Insert mounting screws through mounting
bracket and into wall studs.

Attaching To Wall Anchor

This method allows you to attach mounting
bracket to hollow walls (wall areas between
studs) or to solid walls (concrete or masonry).

Decide which method better suits your needs.
Either method will provide a secure hold for
the mounting bracket.

Removing Front Panel Of Heater

1.

Remove two screws near bottom cor-
ners of front panel.

2.

Lift straight up on grill guard until it stops.
Grill guard will slide up about 1/4".

3.

Pull bottom of front panel forward, then
down.

4.

Remove cardboard packing from grill
and glass.

INSTALLATION

Continued

Marking Screw Locations

1.

Tape mounting bracket to wall where
heater will be located. Make sure
mounting bracket is level.

2.

Mark screw locations on wall (see Fig-
ure 7).

Note: Only mark last hole on each end
of mounting bracket. Insert mounting
screws through these holes only.

3.

Remove tape and mounting bracket
from wall.

Attaching To Wall Stud Method

For attaching mounting bracket to wall studs

1.

Drill holes at marked locations using
9/64" drill bit.

2.

Place mounting bracket onto wall. Line
up last hole on each end of bracket with
holes drilled in wall.

3.

Insert mounting screws through bracket
and into wall studs.

4.

Tighten screws until mounting bracket
is firmly fastened to wall studs.

Attaching To Wall Anchor Method

For attaching mounting bracket to hollow
walls (wall areas between studs) or solid
walls (concrete or masonry)

1.

Drill holes at marked locations using
5/16" drill bit. For solid walls (concrete
or masonry), drill at least 1" deep.

2.

Fold wall anchor as shown in Figure 8.

3.

Insert wall anchor (wings first) into
hole. Tap anchor flush to wall.

4.

For thin walls (1/2" or less), insert red
key into wall anchor. Push red key to
“pop” open anchor wings.

IMPORTANT:

 Do not hammer key!

For thick walls (over 1/2" thick) or solid
walls, do not pop open wings.

5.

Place mounting bracket onto wall. Line
up last hole on each end of bracket with
wall anchors.

6.

Insert mounting screws through bracket
and into wall anchors.

7.

Tighten screws until mounting bracket
is firmly fastened to wall.

Figure 9 - Popping Open Anchor Wings
For Thin Walls

17 

1

/

2

"

Min.

10 

1

/

4

"

Min.

17 

3

/

8

"

Adjoining Wall

Only Insert Mounting 

Screws Through Last 

Hole On Each End

Floor

17 

3

/

8

"

17 

1

/

2

"

Min.

1

/

2

"

Min.

Adjoining Wall

Only Insert Mounting 

Screws Through Last 

Hole On Each End

Floor

Содержание Glo-Warm FA-20BB

























Отзывы: