14
SPECIAL MODE
1. Special mode setting button
b
Press the POWER ON button to turn on while pressing buttons A and B.
Mode
Button A
Button B
Contents
Service Mode
1
4
Version display, LED Check, SW CHECK, VR Check, Total running
time (Clear total runnig time), ROM/RAM Access test, USB MIDI OUT
test, EUP mode test
Version Up Mode
2
3
Firmware Update
2. Service Mode setting button
b
Press the POWER ON button to turn on while pressing buttons 1 and 4.
Select the desired mode and rotate button 5.
No.
Mode
Button 7
Entry
Exit
Contents
1
Version display
REVERB
6
5
Display order
«_SYS»
→
«xxxx(system Ver.)»
→
«_dSP»
→
«xxxx(DSP Ver.)» ever 1 sec.
2
LED Check
FLANGER
6
5
q
All on
w
DIM mode
e
All off
r
Greeen lights up
t
Umber lights up
y
Red lights up
u
Blue lights up
i
7SEG lights up
o
Max Load mode
Q0
TYP lights up mode
3
SW Check
ECHO
6
-
Button displays the number of tests. Press the button and go to the countdown. The
corresponding button is pressed, LED turns off. SW all the press, «PASS» appears.
4
VR Check
DELAY
6
5
Checking the operation of each panel VR.
Turned the volume amount will display in resolution number 1024.
Displays the number corresponding to the selected location of the source selector.
Displays the number corresponding to the position of slide switch.
5
Tatal RunningTime
Display
LOOP
6
5
Total running time displayed. (Max65000hours)
6
ROM/RAM Access
test
B.BREAKER
6
-
FlashROM (2MB) and SD-RAM (8MB) then Reads to accessible. Address (space cache
disabled), and two bytes for each increment.
Press BEAT button.Select run or escape.
Press TAP button.Press the button that is displayed during the run. Start the Access test.
7
USB MIDI OUT
test
FILTER
6
5
"When a PC is not connected state, «FAIL» appears.
Press BEAT button.Select the command button to send.
Press TAP button.USB-Midi sends the selected command."
8
EUP mode test
B.SCRATCH
6
-
"EUP switch ON state.
Press BEAT button.Select run or escape.
Press TAP button.Press the button that is displayed during the run. Start the EUP mode."
1
5 6
2 3 4
7
Содержание DN-X600
