Denon AVR-1404/484, Руководство по эксплуатации

Страница: 16 / 92

• To increase the bass or treble: Turn the
control clockwise. (The bass or treble sound
can be increased to up to +10 dB in steps of
2 dB.)
• To decrease the bass or treble: Turn the
control counterclockwise. (The bass or treble
sound can be decreased to up to –10 dB in
steps of 2 dB.)
16
ENGLISH
3
Select the play mode.
Press the SURROUND MODE button, then turn
the SELECT knob.
Example: Stereo
The volume can be adjusted within the
range of –60 to 0 to 18 dB, in steps of 1 dB.
However, when the channel level is set as
described on page 18, if the volume for any
channel is set at +1 dB or greater, the
volume cannot be adjusted up to 18 dB. (In
this case the maximum volume is adjusted
to “18 dB — (Maximum value of channel
level)”.)
Input mode when playing DTS sources
• Noise will be output if DTS-compatible CDs or LDs
are played in the “ANALOG” or “PCM” mode.
When playing DTS-compatible sources, be sure to
connect the source component to the digital input
jacks (OPTICAL/COAXIAL) and set the input mode
to “DTS”.
4
Start playback on the selected component.
• For operating instructions, refer to the
component’s manual.
5
Adjust the volume.
(Main unit) (Remote control
unit)
The volume level
is displayed on
the master
volume level
display.
To select the surround mode
while adjusting the surround
parameters, channel volume
or tone control, press the
surround mode button then
operate the selector.
(Main unit)
(Main unit) (Remote control unit)
Input mode display
ANALOG DIGITAL
DIGITAL
DIGITAL
ANALOG
AUTO PCM DTS
INPUT
AUTO PCM DTS
INPUT
AUTO PCM DTS
INPUT
AUTO PCM DTS
INPUT
• In the AUTO mode
• In the DIGITAL PCM mode
• In the DIGITAL DTS mode
• In the ANALOG mode
One of these lights,
depending on the input
signal.
Input signal display
SIGNAL
DIGITAL
DIGITAL
DIGITAL
SIGNAL
SIGNAL
• DOLBY DIGITAL
• DTS
• PCM
The indicator lights when digital signals
are being input properly. If the indicator
does not light, check whether the digital input
component setup (page 12) and connections are
correct and whether the component’s power is
turned on.
DIGITAL
DIGITAL
NOTE:
• The indicator will light when playing
CD-ROMs containing data other than audio
signals, but no sound will be heard.
DIGITAL
1 2 3
[1] Adjusting the sound quality (tone)
After starting playback
1
The tone switches as follows each time the
TONE CONTROL button is pressed.
2
With the name of the volume to
be adjusted selected, turn the
SELECT knob to adjust the level.
(Main unit)
3
If you do not want the bass and treble to be
adjusted, turn on the tone defeat mode.
(Main unit)
The signals do not pass
through the bass and treble
adjustment circuits, providing
higher quality sound.
BASS TREBLE
(Main unit)
2
[2] Listening over headphones
1
Connect the headphones to
the PHONES jack of the front
panel.
1
PHONES
NOTE:
To prevent hearing loss, do not raise the volume level
excessively when using headphones.
2
Press the SPEAKER A or B
button turn the speaker off.
(Main unit)
CAUTION: No sound is produced from the
headphones when speakers A or B
are turned on.
1
Use this to turn off the audio
output temporarily.
Press the MUTING button.
Cancelling MUTING mode.
• Press the MUTING
button again.
• Muting will also be cancelled when
MASTER VOL is adjusted up or down.
(Remote
control unit)
[3] Turning the sound off temporarily (muting)
1