10
ENGLISH
Parameter Check
This function enables you to check the measurement results and
equalizer characteristics after Audyssey Auto Setup.
1
8VH
ui
WR VHOHFW ³3DUDPHWHU &KHFN´ DQG WKHQ
SUHVV
ENTER
RU
p
2
8VH
ui
WRVHOHFWWKHLWHP\RXZDQWWRFKHFNWKHQ
SUHVV
ENTER
RU
p
Measurement results for each speaker are displayed.
6SHDNHU&RQILJ&KHFN
'LVWDQFH&KHFN
&KDQQHO/HYHO&KHFN
&URVVRYHU&KHFN
(4&KHFN
5HVWRUH
$8726(783
3$5$0(7(5&+(&.
6KRZVSHDNHUFRQILJXUDWLRQUHVXOW
Speaker Config. Check
Distance Check
Channel Level Check
Crossover Check
EQ Check
Check the speaker configuration.
Check the distance.
Check the channel level.
Check the crossover frequency.
Check the equalizer.
• If “EQ Check” is selected in step 2, press
ui
to select equalizing
curve (“Audyssey” or “Audyssey Flat”) to be checked.
Use
o
p
to switch the display between the different speakers.
3
3UHVV
RETURN
The confirmation screen reappears. Repeat steps 2.
Retrieving Audyssey Auto Setup settings
If you set “Restore” to “Yes”, you can return to Audyssey Auto Setup
measurement result (value calculated at the start by MultEQ® XT)
even when you have changed each setting manually.
Error messages
An error message is displayed if Audyssey® Auto Setup could not be completed due to speaker placement, the measurement environment, etc.
If this happens, check the relevant items, be sure to take the necessary measures, then perform Audyssey Auto Setup over again.
NOTE
Be sure to turn off the power before checking speaker connections.
Examples
Error details
Measures
&DXWLRQ
1RPLFURSKRQHRU6SHDNHU
5HWU\
&KHFNFDXVHRISUREOHP
$8726(783
$8'<66(<$8726(783
5(7851
&DQFHO
0XOW(4;7
• The connected setup microphone is broken,
or a
device other than the supplied setup
microphone is connected.
• Not all speakers could be detected.
• The front L speaker was not properly
detected.
• Connect the included setup microphone to
the SETUP MIC jack of this unit.
• Check the speaker connections.
&DXWLRQ
$PELHQWQRLVHLVWRRKLJK
RU/HYHOLVWRRORZ
5HWU\
&KHFNFDXVHRISUREOHP
$8726(783
$8'<66(<$8726(783
5(7851
&DQFHO
0XOW(4;7
• There is too much noise in the room for
accurate measurements to be made.
• Speaker or subwoofer sound is too low for
accurate measurements to be made.
• Either turn off any device generating noise
or move it away.
• Perform again when the surroundings are
quieter.
• Check the speaker installation and the
direction in which the speakers are facing.
• Adjust the subwoofer’s volume.
&DX LRQ
&KHFNFDXVHRISUREOHP
5HWU\
)URQW5
1RQH
$8726(783
$8'<66(<$8726(783
5(7851
&DQFHO
0XOW(4;7
• The displayed speaker could not be detected. • Check the connections of the displayed
speaker.
&DX LRQ
&KHFNFDXVHRISUREOHP
5HWU\
6NLS
)URQW/
3KDVH
$8726(783
$8'<66(<$8726(783
5(7851
&DQFHO
0XOW(4;7
• The displayed is connected with the
polarities reversed.
• Check the polarities of the displayed
speaker.
• For some speakers, this error message may
be displayed even if the speaker is properly
connected. If you are sure the connection is
correct, press
ui
to select “Skip”, then
press
ENTER
.
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Confirm the setting
Return to previous menu