9
ENGLISH
Basic version
Advanced version
Information
Simple version
12
8VH
ui
WRVHOHFWWKHLWHP\RXZDQW
WRFKHFNDQGWKHQSUHVV
ENTER
>@
67(3&KHFN
&KHFNSURFHVVLQJUHV
XOWV7RSURFHHGSUHVV
´1H[Wµ
6HOHFWLWHPWRFKHFN
6SNU&RQILJ&KHFN
'LVWDQFH&KHFN
&K/HYHO&KHFN
&URVVRYHU&KHFN
1H[W6WRUH
$8726(783
$8'<66(<$8726(783
(17(5
(QWHU
5(7851
&DQFHO
0XOW(4;7
• Subwoofers may measure a greater reported
distance than the actual distance due to added
electrical delay common in subwoofers.
•
If you want to check another item, press
RETURN
.
13
8VH
ui
WR VHOHFW ³1H[W
1
6WRUH´
DQGWKHQSUHVV
ENTER
Set up speakers (Audyssey® Auto Setup)
STEP 4
Calculation
STEP 5
Check
14
6HOHFW³6WRUH´DQGWKHQSUHVV
ENTER
Save the measurement results.
>@
$8726(783
$8'<66(<$8726(783
67(36WRUH
1RZVWRULQJ
3OHDVHZDLW
0XOW(4;7
>@
67(36WRUH
3UHVV´6WRUHµWRVWRUH
FDOFXOD LRQUHVXOWV
$SSO\DQGVWRUHPHDVXUHPHQWUHVXOW
6WRUH
$8726(783
$8'<66(<$8726(783
(17(5
(QWHU
5(7851
&DQFHO
0XOW(4;7
• Saving the results requires about 10 seconds.
• If the measuring results are not to be saved,
press
RETURN
. A message “Cancel Auto
Setup?” will be displayed. Press
o
then select
“Yes”. All the measured Audyssey Auto Setup
data will be erased.
NOTE
During saving of measurement results, be sure
not to turn off the power.
15
8QSOXJ WKH VHWXS PLFURSKRQH IURP
WKHXQLW¶V6(7830,&MDFN
16
6HW'\QDPLF9ROXPH
>@
)LQLVK
6WRULQJFRPSOHWH
$XWR6HWXSLVQRZ
ILQLVKHG3OHDVHXQSOXJ
PLFURSKRQH
7XUQRQ'\QDPLF9ROXPH"
$8726(783
$8'<66(<$8726(783
(17(5
([LW
7XUQ'\QDPLF9ROXPHRQDQGH[LW$XWR6HWXS
<HV
1R
0XOW(4;7
• For details of Dynamic Volume settings, see
page 76.
n
When turning Dynamic Volume on
Use
o
to select “Yes“, and then press
ENTER
.
• The unit automatically enters “Evening” mode.
n
When turning Dynamic Volume off
Use
p
to select “No“, and then press
ENTER
.
NOTE
After performing Audyssey Auto Setup, do not
change the speaker connections or subwoofer
volume. In event of a change, perform Audyssey
Auto Setup again.
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Confirm the setting
Return to previous menu
NOTE
• If the result differs from the actual connection
status, or if “Caution!” is displayed, see “Error
messages” (
v
page 10). Then carry out Audyssey
Auto Setup again.
• If the result still differs from the actual connection
status after remeasurement or the error message
still appears, it is possible that the speakers
are not connected properly. Turn this unit off,
check the speaker connections and repeat the
measurement process from the beginning.
• If you change speaker positions or orientation,
perform Audyssey Auto Setup again to find the
optimal equalizer settings.
11
2Q WKH
STEP3
VFUHHQ XVH
ui
WR VHOHFW ³1H[W
1
&DOFXODWLRQ´ DQG
WKHQSUHVV
ENTER
Measuring results are analyzed, and the
frequency response of each speaker in the
listening room is determined.
>@
$8726(783
$8'<66(<$8726(783
67(3&DOFXODWLRQ
1RZFDOFXODWLQJ
3OHDVHZDLW
0XOW(4;7
• Analysis takes several minutes to complete. The
time required for this analysis depends on the
number of speakers connected.
The more connected speakers there are, the
longer it takes to perform analysis.
STEP 6
Store
Finish
