DENGENSHA WS-100 Скачать руководство пользователя страница 33

Страница: 33 / 39

DENGENSHA



USB cable

USB interface of WS-100 transfers measurement data to the PC.

※

note: PC needs to be installed software (WDM).

Please refer to the separate instruction manual "OPI-0002" for WDM.

9. Battery

9 - 1. Mounting battery

AA nickel-metal hydride battery × 4

Open the back cover of the body, and put the battery as shown in Figure the battery box.

Please put it correctly according to the polarity that is displayed in the battery box.

Fig. 4

Built-in battery polarity direction

9 - 2. Battery charging instructions

①

The built-in battery properly Be sure to note the polarity, and close the back cover, Check

([POWER] lamp is off.

②

Connect DC power connector to WS-100, and connect AC adapter to AC plug.

Battery charging will start.

Temperature range of under charge : 5

℃

~ 30

℃

Please keep temperature rage when battery charging.

Over range temperature may cause abnormal charging.

③

CHARGE lamp (Red)

Under normal charging.

: Blinking slowly (once per second).

Under abnormal charging.

: Blinking fast.(4 times per second)

Charge complete or unable to charge : Turn off

When abnormal charging or unable to charge happens,

Please stop charging.

Please confirm temperature, and battery polarity direction.

Mandatory

action

Battery polarity direction should be Fig.4.

Содержание WS-100








































Результаты поиска

Содержание WS-100

Отзывы:

Похожие инструкции для WS-100

Бренды по названию

Популярные бренды

DENGENSHA WS-100, Инструкция по эксплуатации

Результаты поиска

Содержание WS-100

Отзывы:

Похожие инструкции для WS-100

Бренды по названию

Популярные бренды