background image

I-974

 

Rev. J-43816

 

Page 6 of 8

 3/23/18

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F

 Dip Switches 

The following diagram illustrates what the different switches refer to so that the Nitro Express can be set up for the 
proper situation. 

The dip switches are set up so that the “up” position is “on” and the “down” position is “off”. 

 
 
 
 

 

ON 

PRESS DOWN THIS 

WAY FOR ON 



PRESS DOWN THIS 

 

WAY FOR OFF 

OFF 

 
 
 
 
 
 

Potentiometers (Knobs) 

The potentiometers can be set according to the following charts. Each of the next four figures will outline various 
configurations that are possible. For more information on these configurations consult pages 5-6 to see how to set up the 
dip switches for the configurations. 

 

Rinse/Sanitizer Settings 

3 7 

2 8 

0 10 

Rinse 

The Rinse and Sanitizer knobs control the same setting 
whether in probe or probeless mode and in door or conveyor 
mode. They control the speed of the rinse and sanitizer pump. 

 

The table to the right has approximate values for the pump 
rate at different settings of the knob. 

 

Only the DLL and LLL models have a sanitizer 
potentiometer. 

 

Probeless and Door Configuration 

 

3 7 

2 8 

0 10 

Detergent 

 
 

3 7 

2 8 

0 10 

Initial Detergent Charge – 

The detergent knob sets the time the 

detergent pump will run or detergent valve will remain open during an 
initial charge. The time can be set from 0-60 sec. 

 

The initial charge is activated in one of two ways. 

1.

 

It can be activated by 1 hour of elapsed time where no triggers have 
activated the dispenser. 

2.

 

With the rinse limit turned on (switch 7) and a rinse trigger active for 
more than 20 seconds, an initial charge will be dispensed. 

 

Dead Cycles – 

The alarm knob sets the number of cycles no 

detergent is dispensed before a recharge portion of detergent is added 
to the machine. 

 

The table to the right has the different settings for the Dead Cycle 
count corresponding to the knob setting. 

Alarm (Dead Cycles) 

PRO

BEL

ES

S

 

MOD

E

 

CONC

EN. 

MOD

E

 

CON

V

EYOR 

MOD

E

 

D

OOR

 MODE 

NO

RM

AL 

RAN

G

E

 

H

IGH

 RA

N

G

PUL

SE FE

ED

 

OFF 

PUL

SE FE

ED 

ON 

PLU

S

 0 SE

C

 

RI

N

SE 

DEL

A

Y

 

PLU

S

 2 SE

RI

N

SE D

E

L

A

Y

 

PLU

S

 0 SE

C

 

RI

N

SE 

DEL

A

Y

 

PLU

S

 4 SE

RI

N

SE D

E

L

A

Y

 

20 S

E

CO

ND 

RI

N

SE LI

MI

T

 

ON 

RI

N

SE LI

MI

T

 

OFF 

ALA

R

M VO

L

 

LOW 

ALA

R

M VO

H

IGH 

RINSE/ 

SANITIZER 

SETTING

 

PUMP RATE

0 ml/min 

8.5 ml/min

27 ml/min 

33 ml/min 

40 ml/min 

10 

43 ml/min 

DETERGENT

INITIAL 

CHARGE 

SETTING 

0-60 sec 

0-170 ml 

0-5.75 oz 

ALARM

SETTING

DEAD 

CYCLES

Содержание NITRO EXPRESS









Отзывы: