background image

 

Switch Setting Descriptions: 

The DIP Switches can only be changed when AC drive is in a stopped mode.   

 Indicates the position of the switch (ON/OFF). 

 

DIP 

Switch 

Switch  

Name 

Switch Setting 

Parameter Descriptions 

Maximum Output Frequency 

V/F Curve 

ON

1 2 3 4 5 6 7

50Hz 

100%

50Hz

f

 

ON

1 2 3 4 5 6 7

60Hz 

100%

60Hz

f

 

ON

1 2 3 4 5 6 7

100Hz 

100%

50Hz 100Hz

f

 

Max. 

Output 

Frequency 

ON

1 2 3 4 5 6 7

120Hz 

100%

60Hz 120Hz

f

 

ON

1 2 3 4 5 6 7

Reverse enable 

Reverse 

Inhibit 

ON

1 2 3 4 5 6 7

Reverse disable 

ON

1 2 3 4 5 6 7

Low torque output 

Torque 

Setting 

ON

1 2 3 4 5 6 7

High torque output 

ON

1 2 3 4 5 6 7

Applicable for 40/100W motor 

Electronic 

Thermal 

Setting 

ON

1 2 3 4 5 6 7

Applicable for 25/60W motor 

ON

1 2 3 4 5 6 7

Operation command controlled by potentiometer. 

Operation 

Command 

Source 

Select (1) 

ON

1 2 3 4 5 6 7

Operation command controlled by external terminal 

ON

1 2 3 4 5 6 7

Operation command controlled by external terminal 
(can be monitored by communication mode) 

Operation 

Command 

Source 

Select (2) 

ON

1 2 3 4 5 6 7

Switch 7 is ON, indicates the communication mode is 
enabled; switches 1 to 6 are address settings. 

Содержание VFD-L

















Отзывы: