background image

6

Quick installation guide for RPI M50A inverters

Planning the installation

5

>50 cm

>30 cm

>30 cm

>30 cm

>20 cm

 

Ensure adequate air circulation  Hot air must be able 
to dissipate upward  Keep enough space around each 
inverter 

 

Do not install inverters directly above one another  
Otherwise, the upper inverter is warmed up by the 
lower one 

 

Consider the 

operating temperature range

 (see sec-

tion “Technical data”)  

When the operating temperature range is exceeded, 
the solar inverter reduces the amount of power gener-
ated  

Ambient temperature and air circulation

Outdoor installations

 

The solar inverter has protection 
degree IP65 and can be installed 
indoors or in protected outdoor 
areas (that means outdoor but 
protected by a roof against direct 
sun, rain or snow) 

 

Mount the solar inverter vertically 

Where to mount the inverter

??

??

 

Mount the solar inverter so that the 
LEDs and display can be easily seen 
and that the buttons can be operated  
Make sure the reading angle and instal-

lation height are sufficient.

 

Always use the mounting plate 
supplied with the solar inverter 

 

Check that the wall is capable 
of bearing the heavy load of the 
device 

 

Use dowels and screws that are 
suitable for the wall material and 
the heavy weight 

 

Mount the solar inverter on a 
vibration-free wall to avoid disrup-
tive vibrations 

 

Possible noise emissions can 
be disruptive when the device is 
used in living areas or in buildings 
with animals  Therefore, choose 
your installation location carefully 

Mounting orientation

 

The solar inverter is very heavy, 
see section “Technical data”  The 
solar inverter must be lifted and 
carried by at least three people  

74 kg

Содержание RPI M50A 120





















Отзывы: