background image

10

Quick installation guide for RPI M50A inverters

Connecting to the solar modules (DC) 

8

DISCONN AC/DC

OFF

ON

It is recommended to use a special open-
end spanner for the MC4 DC connectors if 
you need to disconnect MC4 DC connec-
tors  from the inverter  Otherwise you might 
destroy the DC Connectors 

DANGER

Risk of death or serious injury from electrocution

Potentially fatal voltage may be applied to the DC connections of the solar in-
verter  When light is falling on solar modules, they immediately start producing 
energy  They do so, even when the sun is not shining 

 

Never disconnect the solar modules when the solar inverter is powered  

 

First switch off the grid connection so that the solar inverter cannot feed 
energy into the grid  

 

Turn the AC/DC isolating switch to position 

OFF

 

 

Make sure the DC connections cannot be accidentally touched 

 

Check the polarity of the DC voltage before 
you connect the solar modules 

 

To ensure protection degree IP65, cap all 
unused connectors with the caps delivered 
with the inverter 

DC connectors on the inverter

Plugs for DC cable

a

b

Multi-Contact

mm

2

mm

DC–

^

1 5 / 2 5

3-6

32 0010P0001-UR

5 5-9

32 0012P0001-UR

4 / 6

3–6

32 0014P0001-UR

5 5-9

32 0016P0001-UR

DC+

1 5 / 2 5

3-6

32 0011P0001-UR

5 5-9

32 0013P0001-UR

4 / 6

3-6

32 0015P0001-UR

5 5-9

32 0017P0001-UR

a

b

DC Inputs

DC INPUT

DC 1

DC 2

+

+

+

+

DC cable specifi cation

DC INPUT

DC 1

DC 2

+

+

+

+

France: Safety caps are needed for each 
DC input that is connected to a string of 
solar modules 

Содержание RPI M50A 120





















Отзывы: