background image

2- ENG

A08184

SAFETY GUIDELINES - DEFINITIONS

Indicates an 
imminently hazardous 

situation which, if not avoided, 

will result 

in 

death or serious injury.

Indicates a potentially  
hazardous situation 

which, if not avoided, 

could result in 

death or serious injury.

Indicates a potentially 
hazardous situation 

which, if not avoided, 

may result in minor 

or moderate injury.

Used without the 
safety alert symbol 

indicates a potentially hazardous situation 
which, if not avoided, 

may result in  

property damage

.

This manual contains information that is important for you to know and 

understand. This information relates to protecting 

YOUR SAFETY and 

PREVENTING EQUIPMENT PROBLEMS. To help you recognize this 

information, we use the symbols below. Please read the manual and pay 

attention to these symbols.

IMPORTANT SAFETY INSTRUCTIONS

Some dust created by power sanding, sawing, grinding, 

drilling, and other construction activities contains 

chemicals known (to the State of California) to cause cancer, birth defects 

or other reproductive harm. Some example of these chemicals are:
• 

lead from lead-based paints

• 

crystalline silica from bricks and cement and other masonry products

• 

arsenic and chromium from chemically-treated lumber

Your risk from these exposures varies, depending on how often you do 

this type of work. To reduce your exposure to these chemicals: work in 

a well ventilated area, and work with approved safety equipment, always 

wear MSHA/NIOSH approved, properly fitting face mask or respirator when 

using such tools.
When using air tools, basic safety precautions should always be followed 

to reduce the risk of of personal injury.

Содержание 66-651-1



























Отзывы: