5
ADDITIONAL SPECIFIC SAFETY RULES
1.
DO NOT OPERATE THIS MACHINE
until it is completely
assembled and installed according to the instructions. A
machine incorrectly assembled can cause serious injury.
2.
OBTAIN
ADVICE
from your supervisor, instructor, or
another qualified person if you are not thoroughly familiar
with the operation of this machine. Knowledge is safety.
3.
FOLLOW ALL WIRING CODES
and recommended
electrical connections to prevent shock or electrocution.
4.
SECURE THE MACHINE TO A SUPPORTING SURFACE.
Vibration can cause the machine to slide, walk, or tip over.
5.
NEVER START THE MACHINE BEFORE CLEARING
THE TABLE OF ALL OBJECTS
(tools, scrap pieces,
etc.).
Debris
can be thrown at high speed.
6.
NEVER START THE MACHINE
with the drill bit, cutting
tool, or sanding drum against the workpiece. Loss of
control of the workpiece can cause serious injury.
7.
PROPERLY LOCK THE DRILL BIT, CUTTING TOOL, OR
SANDING DRUM IN THE CHUCK
before operating this
machine.
8.
REMOVE THE CHUCK KEY BEFORE STARTING THE
MACHINE.
The chuck key can be thrown out at a high
speed.
9.
TIGHTEN ALL LOCK HANDLES
before
starting the
machine.
Loss of control of the workpiece can cause
serious injury.
10.
USE ONLY DRILL BITS, CUTTING TOOLS, SANDING
DRUMS, OR OTHER ACCESSORIES
with shank size
recommended in your instruction manual. The wrong
size accessory can cause damage to the machine and/or
serious injury.
11.
USE ONLY DRILL BITS, CUTTING TOOLS, OR
SANDING DRUMS
that are not damaged. Damaged
items can cause malfunctions that lead to injuries.
12.
USE RECOMMENDED SPEEDS
for all operations. Other
speeds may cause the machine to malfunction causing
damage to the machine and/or serious injury.
13.
AV O I D AW K WA R D O P E R AT I O N S A N D H A N D
POSITIONS.
A sudden slip could cause a hand to move
into the bit.
14.
KEEP ARMS, HANDS, AND FINGERS
away from the bit.
Serious injury to the hand can occur.
15.
HOLD THE WORKPIECE FIRMLY AGAINST THE
TABLE.
Do not attempt to drill a workpiece that does
not have a flat surface against the table, or that is not
secured by a vise. Prevent the workpiece from rotating
by clamping it to the table or by securing it against the
drill press column. Loss of control of the workpiece can
cause serious injury.
16.
TURN THE MACHINE “OFF” AND WAIT FOR THE DRILL
BIT, CUTTING TOOL, OR SANDING DRUM TO STOP
TURNING
prior to cleaning the work area, removing
debris, removing or securing workpiece, or changing
the angle of the table. A moving drill bit, cutting tool, or
sanding drum can cause serious injury.
17.
PROPERLY SUPPORT LONG OR WIDE
workpieces.
Loss of control of the workpiece can cause severe injury.
18.
NEVER PERFORM LAYOUT, ASSEMBLY OR SET-UP
WORK
on the table/work area when the machine is
running. Serious injury can result.
19.
TURN THE MACHINE “OFF”,
disconnect the machine
from the power source, and clean the table/work area
before leaving the machine.
LOCK THE SWITCH IN THE
“OFF” POSITION
to prevent unauthorized use. Someone
else might accidentally start the machine and cause
serious injury to themselves.
20.
ADDITIONAL INFORMATION
regarding the safe and
proper operation of power tools (i.e., a safety video)
is available from the Power Tool Institute, 1300
Sumner Avenue, Cleveland, OH 44115-2851 (www.
powertoolinstitute.com). Information is also available
from the National Safety Council, 1121 Spring Lake
Drive, Itasca, IL 60143-3201. Please refer to the
American National Standards Institute ANSI 01.1 Safety
Requirements for Woodworking Machines and the
U.S. Department of Labor OSHA 1910.213 Regulations.
FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY.
ADDITIONAL SAFETY RULES FOR THE LASER
EYE INJURY – LASER LIGHT
Do not stare into beam aperture, or into a reflection from a mirror-like surface.
Do not use optical tools such as a telescope or transit to view the laser beam.
EYE INJURY – LASER LIGHT
Do not operate the laser around children or allow children to operate the laser.
Store idle laser out of reach of children and other untrained persons.
Turn the laser off when it is not in use.
Do not disassemble laser module. The class II laser output could be exceeded if the unit is disassembled. Laser complies with 21
CFR 1040.10 and 1040.11.
Use of controls or adjustments or performance of procedures other than those specified herein may result in
hazardous radiation exposure.
EXPLOSION HAZARD.
Do not operate the laser or drill press in explosive atmospheres such as in the presence of
flammable liquids, gases, or dust. A spark could ignite the dust or fumes.
NOTE:
Do not remove or deface warning labels.
Содержание 17-959L
Страница 59: ...59 NOTES NOTES NOTAS...
