13
discharge steam for more than 3 minutes at a time);
8� When you have obtained the required froth, stop steam
delivery by turning the steam dial back to the 0 position�
Danger of scalding!
Stop steam delivery before removing the container with the
frothed milk to avoid burns caused by splashes of boiling milk�
9� Add the milk froth to the coffee prepared previously�
The cappuccino is ready� Sweeten to taste and, if desired,
sprinkle a little cocoa powder on the froth�
Press any button to exit the steam function�
Making hot milk (not frothed)
To make hot milk without froth, proceed as described in the
above section, making sure the cappuccino/hot milk toggle of
the cappuccino maker is positioned upwards in the “HOT MILK”
position�
Cleaning the cappuccino maker after use
Clean the cappuccino maker each time you use it to avoid the
build-up of milk residues or blockages�
Danger of scalding!
When cleaning the cappuccino maker, a little hot water is
delivered�
Avoid contact with splashes of water�
1� Let a little water run for a few seconds by rotating the
steam dial to the I position�
Then turn the steam dial to the 0 position to stop the flow
of hot water�
2� Wait a few minutes for the cappuccino maker to cool
down� Turn the cappuccino maker from right to left and
then pull downwards to remove it (fig� 22)�
3� Move the cappuccino/hot milk toggle upwards (fig� 23)�
4� Slide the nozzle downwards (fig� 24)�
5� Make sure the two holes shown by the arrows in fig� 25 are
not blocked� If necessary, clean with a pin�
6� Replace the nozzle, move the toggle downwards and
put the cappuccino maker back on the nozzle (fig� 26),
inserting it upwards and turning it left to right until it is
attached�
MAKInG Hot WAteR
Danger of scalding!
Never leave the machine unsupervised while hot water is being
delivered�
The hot water spout becomes hot while water is being delivered
and must be held by the handle only�
1� Place a container under the cappuccino maker (as close as
possible to avoid splashes)�
2� Turn the steam dial to the I position� Hot water starts to be
delivered
3� Stop by turning the steam dial to the
0
position�
Please note:
If “Energy Saving” mode is active, you may have to wait a few
seconds before the hot water is delivered�
CLeAnInG
Cleaning the machine
The following parts of the machine must be cleaned regularly:
- coffee grounds container (A14),
- drip tray (A18) and condensate tray (A15),
- water tank (A10),
- coffee spouts (A13),
- pre-ground coffee funnel (A6),
- inside of the machine, accessible after opening the infuser
door (A11),
- infuser (A12)�
Important!
• Do not use solvents, abrasive detergents or alcohol to
clean the machine� You do not need to use chemical
products to clean De’Longhi bean to cup coffee machines�
The descaler recommended by De’Longhi is made from
natural and completely biodegradable substances�
• None of the components can be washed in a dishwasher.
• Do not use metal objects to remove encrustations or coffee
deposits as they could scratch metal or plastic surfaces�
Cleaning the coffee grounds container
When the
indicator flashes, the coffee grounds container
must be emptied and cleaned� Unless you clean the grounds
container, the indicator will continue to flash and the appliance
cannot be used to make coffee�
To clean (with the machine turned on):
• Remove the drip tray (fig. 27), empty and clean.
• Empty the grounds container and clean thoroughly to
remove all residues left on the bottom�
• Check the red condensate tray and empty if necessary�
Important!
When removing the drip tray, the grounds container must be
emptied, even if it contains few grounds�
If this is not done, when you make the next coffees, the
grounds container may fill up more than expected and clog the
machine�
Cleaning the drip tray and condensate tray
Important!
If the drip tray is not emptied regularly, the water could
