DeLonghi ESAM 4200, Инструкция по эксплуатации

Страница: 11 / 21

normal operation indicator lights”).
A few moments before the lights stop flashing
the machine automatically performs a rinse
cycle: a little hot water will come out of the
delivery spouts and will be collected in the
drip tray underneath.
Tip: for a hotter, short coffee (less than 60ml),
first fill the cup with the hot rinsing water.
Then leave it inside for a few seconds (before
emptying it) so as to pre-heat the cup.
6. At this point, the machine is ready for use.
PREPARING THE COFFEE
(USING COFFEE BEANS)
Important! Do not use caramelised or
candied coffee beans as they could stick to the
coffee mill and make it unusable.
1) Before delivering the coffee, always make
sure that the green and lights
are on steady, that the water tank and the cof-
fee bean container are full.
2) Adjust the right-hand Grinding quantity selec-
tor knob (Fig. 7) to set the desired taste of the
coffee. Turning the knob clockwise increases
the quantity of coffee beans that the machine
will grind, and thus makes the taste of the cof-
fee stronger. When using the machine for the
first time, the correct position of the knob can
be found by trial and error. Make sure not to
turn it too far clockwise, otherwise the coffee
will be delivered too slowly (in drops), above
all when preparing two cups of coffee.
3) Adjust the left-hand knob (Fig. 8) to set the
quantity of coffee required. Turning the knob
clockwise makes a longer coffee. When using
the machine for the first time, the correct posi-
tion of the knob can be found by trial and error.
4) Place one cup under the spouts to make 1
coffee (Fig. 9) or 2 cups for 2 coffees (Fig.
10). For a creamy coffee, lower the spouts to
bring them as close to the cups as possible
(Fig. 11).
5) Press the button (Fig. 12) to make one cup
of coffee or the button (Fig. 13) to make
2 coffees. At this point the machine grinds the
beans, runs a short pre-infusion cycle, a
pause and then completes the delivery.
Once the desired quantity has been reached,
the machine automatically stops delivering
the coffee and discharges the grounds into
the special container.
6) After a few seconds, when both the green
and indicator lights are on again, ano-
ther coffee can be made.
7) To switch the machine off, press the but-
ton. (Before switching off, the machine auto-
matically runs a rinse cycle: a little hot water
will come out of the spouts and will be collec-
ted in the drip tray underneath - be careful, to
avoid being scalded ). If the machine is not
switched off using the button, it will
switch itself off and run a brief rinse cycle 3
hours after the last operation.
NB!
1) If the coffee is delivered a drop at a time or
not at all, turn the grinding coarseness regu-
lator adjustment knob (S) found inside the-
container for coffee beans (T) one click anti-
clockwise (see fig 17). Turn a click at a time
until the coffee is delivered satisfactorily.
2) If the coffee is delivered too fast and is not
creamy enough, turn the right-hand Grinding
quantity selector knob found on the control
panel (fig. 7) clockwise. Proceed by trial and
error to find the correct position of the knob.
Make sure not to turn the knob too far clock-
wise, otherwise the delivery may become too
slow (in drops), above all when making two
cups of coffee. If, after several coffees, the
cream is still not satisfactory, also turn the
grinding adjustment knob (Fig. 17) one click
clockwise (see “Regulating the coffee mill”).
3) Tips on making hotter coffee:
1) If, when the machine has just been turned
on, a short cup of coffee is required (less than
60ml), use the hot rinsing water to pre-heat
the cups.
If, on the other hand, more than 2/3
minutes have elapsed since the last coffee
was made, before preparing another coffee
the infuser must be pre-heated, pressing the
button (Fig. 14).
Then let the water flow out into the drip tray
underneath, or alternatively use this water to
fill (and then empty) the cup to be used for the
coffee, so as to pre-heat it.
2) Unless preheated, do not use cups that are
too thick, as they will absorb too much heat.
3) Use cups that have been previously heated
by rinsing them with hot water or alternatively
by leaving them for at least 20 minutes on the
cup warmer tray on top of the machine with
the appliance on.
10