DeLonghi ECP31.21, Руководство пользователя

Страница: 8 / 22

16
• Water penetrating the cofee machine could cause
damage.
Do not place the appliance near taps or sinks.
• The appliance could be damaged if the water it contains
freezes.
Do not install the appliance in a room where the tempera-
ture could drop below freezing point.
• Arrange the cord in such a way that it cannot be damaged
by sharp edges or contact with hot surfaces (e.g. electric
hot plates).
• The appliance gives of heat.
After positioning the appliance on the worktop, leave a
space of at least 3 cm between the surfaces of the appli-
ance and the side and rear walls and at least 15 cm above
the cofee machine.
Connecting the appliance
Danger!
Check that the mains power supply voltage corresponds to that
indicated on the rating plate on the bottom of the appliance.
Connect the appliance to an eiciently earthed and correctly
installed socket with a minimum current rating of 10A only.
If the power socket does not match the plug on the appliance,
have the socket replaced with a suitable type by a qualiied
electrician.
FILLING THE WATER TANK
1. Open the lid of the appliance (ig. 1) then extract the tank
by pulling upwards (ig. 2);
2. Fill the tank with fresh clean water, taking care not to ex-
ceed the MAX level (ig. 3).
Put the tank back in the appliance, pressing lightly to open
the valves located on the bottom of the tank.
3. More simply, the tank can also be illed without removing
it, pouring the water directly from a jug.
Important:
Never operate the appliance without water in the tank or with-
out the tank.
Check the level of water in the tank through the viewing win-
dow (A12).
SETTING UP THE APPLIANCE
1. Turn the appliance on by pressing the ON/OFF button (ig.
4): the power light I comes on.
2. Insert the required cofee ilter in the ilter holder (ig. 5).
3. Attach the ilter holder onto the machine without illing it
with ground cofee (ig. 6).
4. Place a 0.5 litre container under the boiler outlet and an-
other 0.5 litre container under the cappuccino maker.
5. Wait until the OK light comes on (ig. 8) and immediately
afterwards turn the mode selector dial to the
position (ig. 9) and deliver about half the tank through the
ilter holder.
6. Then turn the steam dial to the position (ig. 10)
and deliver all the water remaining in the tank through the
cappuccino maker.
7. Turn the steam dial back to the
0
position and the mode
selector dial to the
l
position (STAND-BY).
8. Empty the two containers and replace them under the
boiler outlet and the cappuccino maker and repeat points
5-6-7.
Now the appliance is ready for use.
Auto-of
If the appliance is not used for a certain period of time (variable
according to the model), it turns of automatically (the power
light goes out).
Tips for a hotter cofee
To make espresso cofee at the right temperature, the cofee
maker should be preheated as follows:
1. Turn the appliance on by pressing the ON/OFF switch (the
ON light comes on) (ig. 4) and attach the ilter holder to
the appliance without adding pre-ground cofee (ig. 6).
2. Place a cup under the ilter holder. Use the same cup as will
be used to prepare the cofee in order to preheat it.
3. Wait until the OK light comes on (ig. 8) and immediately
afterwards turn the selector dial to the position
(ig. 9) and let water discharge until the
OK
light turns of,
then interrupt by turning the dial to the
I
position.
4. Empty the cup, wait until the
OK
light comes on again and
then repeat the same operation.
(It is normal for a small and harmless puf of steam to be given
of when removing the ilter holder).
Mugs or glasses tray (models ECP35.31 and
ECP33.21 only)
If you are using tall cups or glasses (for example, to make long
cofee or macchiato),extract the drip tray and rest the cup di-
rectly on the mugs or glasses tray (A14 - ig. 11).
Once you have made your cofee, put the drip tray back in
position.