9
SWING FUNCTION
The swing button (D6) activates and deactivates the swing fun-
ction. When the internal fan is running, the swing function di-
stributes the air evenly into the room moving the flap forwards
and backwards alternatively. If pressed again, the flap will be
locked into its current position.
NOTE
: If the internal fan is not
running, the swing function will also not operate. In order to avoid
damaging the internal mechanisms, the flap must not be moved
manually.
SETTING THE TIMER
The timer allows the delayed start up or shut down of the appli-
ance. This function will prevent wasting electricity by optomiz-
ing the operating periods.
How to program delayed shut down
• While the appliance is on in any operating mode, delayed
shut down can be programmed.
• Press the
C1
C2
C4
C11
C13
C12
C9
C7
C5
C6
C3
C16
C14
C10
C15
C17
C8
timer button (D7), the timer symbol (C13)
and hours (C14) light up.
•
Press the (D3) and (D4)
buttons until the desired
number of hours to shut down appears on the display.
A few seconds after the timer is set, the setting is memorized
and the display shows the operating mode and the timer symbol
stays lit. Once the set time is elapsed, the air conditioner goes
into standby. To cancel the timer program, press the
C1
C2
C4
C11
C13
C12
C9
C7
C5
C6
C3
C16
C14
C10
C15
C17
C8
timer
button (D7) twice. The timer symbol (C13) will go off.
Note:
Once the timer has been activated, by pressing the timer button
only one time, the remaining hours until shut down will be displayed.
How to program delayed start up
• Plug in the appliance and set to standby.
•
Press the
C1
C2
C4
C11
C13
C12
C9
C7
C5
C6
C3
C16
C14
C10
C15
C17
C8
timer button (D7), the timer symbol (C13) and
hours (C14) light up.
•
Press the (D3) and (D4)
buttons until the desired
number of hours to start up appears. Start up can be pro-
grammed at any time in the next 24 hours.
When the set time is elapsed, the appliance will start to operate
in the same operating mode that was previously set.
To cancel the timer program, press the timer button (D7) twice.
The timer symbol (C13) will go off.
Note:
Once the timer has been activated, by pressing the timer key
only one time, the remaining hours to the start up will be displayed.
Note:
•
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reason-
able protection against harmful interference in a residen-
tial installation.
• This equipment generates, uses and can radiate radio fre-
quency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee
that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio
or television reception, which can be determined by turn-
ing the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment into an outlet on a circuit differ-
ent from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician
for help.
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s au-
thority to operate the equipment.
• This device complies with Part 15 of the FCC Rules. Opera-
tion is subject to the following two conditions: (1) this de-
vice may not cause harmful interference, and (2) this device
must accept any interference received, including interfer-
ence that may cause undesired operation.
• This Class B digital apparatus complies with Canadian CAN
ICES-3 (B) / NMB-3 (B).
FCC Responsible party:
De Longhi America
Upper Saddle River NJ 07452
201-919-4000
