Dell S6100 Скачать руководство пользователя страница 9

Страница: 9 / 54

MAC address

Express service code

System status

You can view S6100–ON status information using the LEDs.

LED display

The S6100–ON includes LED displays on the I/O side of the system.

NOTE:

If you are installing third-party software, for LED information, see your third-party operating software documentation.

LED behavior

The following S6100–ON system LED behavior is seen during open networking installation environment (ONIE) operations:

Figure 5. S6100–ON LEDs

Fan LED

Power LED

Master LED

System LED

Locator LED

System LED

Port LEDs

Stack ID LED

RJ-45 Ethernet Management Port LED

Table 1. S6100–ON LED behavior

LED

Description

System Status and Health LED

•

Off—No power

•

Solid green—Normal Operation

•

Blinking green—POST is in process

•

Solid amber—Critical system error

S6100–ON system

Содержание S6100























































Результаты поиска

Содержание S6100

Отзывы:

Похожие инструкции для S6100

Бренды по названию

Популярные бренды

Dell S6100, Руководство по установке

Результаты поиска

Содержание S6100

Отзывы:

Похожие инструкции для S6100

Бренды по названию

Популярные бренды