Dell S6100 Скачать руководство пользователя страница 11

Страница: 11 / 54

LED

Description

•

Flashing amber, ~30 ms—Port link is 4x10 GbE

Table 4. QSFP28 Port LEDs—2x40GbE Mode

LED

Description

Link LED

•

Off—No Link

•

Solid green—Port link is 2x40 GbE

Activity LED

•

Off—No Link

•

Flashing amber, ~30 ms—Port link is 2x40 GbE

Table 5. SFP+ port LEDs

LED

Description

Link LED

•

Off—No Link

•

Solid green—Port activity operating at maximum port speed

•

Solid amber—Port activity operating at lower speed

Activity LED

•

Off—No Link

•

Flashing green, ~30 ms—port activity operating at maximum

port speed

•

Flashing amber, ~30 ms—port activity operating at lower port

speed

Prerequisites

The following is a list of components required for successful installation of the S6100-ON:

NOTE:

Detailed installation instructions for the S6100-ON are provided in

Site preparations

and

S6100-ON Installation

•

S6100–ON chassis or multiple chassis, if stacking

•

AC or DC country and regional-specific cables to connect the AC or DC power source to each of the chassis’ AC or DC power supplies

•

Mounting brackets for rack installation, included

•

Screws for rack installation

•

#1 and #2 Phillips screw drivers, not included

•

Torx screwdriver, not included

•

Ground cable screws, included

•

Copper or fiber cables

Other optional components are:

•

Ground cable

•

Extra power supply unit

•

Extra fan module

•

Extra mounting brackets

S6100–ON system

Содержание S6100























































Результаты поиска

Содержание S6100

Отзывы:

Похожие инструкции для S6100

Бренды по названию

Популярные бренды

Dell S6100, Руководство по установке

Результаты поиска

Содержание S6100

Отзывы:

Похожие инструкции для S6100

Бренды по названию

Популярные бренды