Dell S6100 Скачать руководство пользователя страница 50

Страница: 50 / 54

Parameter

Specifications

Storage Humidity

5 to 95 percent, non-condensing

Thermal Output

Typical: 1170.4 BTU/hr (343 W)

Maximum: 3057.3 BTU/hr (896 W)

Maximum operational altitude

10,000 feet (3,048 meters)

Maximum non-operational altitude

No performance degradation to 35,000 feet (10,668 meters)

Shock

SV0115 — ODM

Table 12. AC power requirements

Parameter

Specifications

Power Supply

100–240 VAC 50/60 Hz

Maximum Current Draw Per System

12A–6.5A @ 100–240 VAC

PSU Maximum Power Capability

1100 Watts

Typical and Maximum Power Consumption

343 Watts typical

896 Watts maximum

Reliability

MTBF 1,154,397 hours

Table 13. DC power requirements

Parameter

Specifications

PSU Maximum Power Capability

1100 Watts

PSU Maximum current required

32A

Minimum and maximum input voltage range

−40.5 V / −48 V/ −60 V

Input power at full load

−40.5 V/970 W −48 V/930 W −60 V/950 W, without fan

−40.5 V/980 W −48 V/940 W −60V/ 960 W, with fan

Input current at full load

−40.5V/23.8A −48V/19.0A −60V/ 15.6A, without fan

−40.5V/24.0A −48V/19.2A −60V/ 16.0A, with fan

Start up VDC

39.0+/−1.5 V

Start off VDC

37.5+/−1.5 V

IEEE standards

The S6100–ON complies with the following IEEE standards:

•

802.3ab Gigabit Ethernet (1000BASE-T)

•

802.3ae 10 Gigabit Ethernet (10GBASE-X)

•

802.3ba 40 Gigabit Ethernet (40GBase-SR4, 40GBase-CR4) on optical ports

•

802.3ba 100 Gigabit Ethernet

•

802.3bj 100 Gigabit Ethernet

Specifications

Содержание S6100























































Результаты поиска

Содержание S6100

Отзывы:

Похожие инструкции для S6100

Бренды по названию

Популярные бренды

Dell S6100, Руководство по установке

Результаты поиска

Содержание S6100

Отзывы:

Похожие инструкции для S6100

Бренды по названию

Популярные бренды