Dell Precision Workstation M6400 Скачать руководство пользователя страница 69

Страница: 69 / 81

Card Cage: Dell Precision M6400 Service Manual

file:///T|/htdocs/systems/wsm6400/en/sm/cardcage.htm[11/16/2012 10:27:21 AM]

Replacing the Card Cage

CAUTION:

Before working inside your computer, read the safety information that shipped with your

computer. For additional safety best practices information, see the Regulatory Compliance Homepage on

www.dell.com at: www.dell.com/regulatory_compliance.

1. Connect the card cable to the I/O board.

2. Place the card cage on the base assembly.

3. Replace the four M2 x 3-mm screws.

4. Replace the palm rest (see

Replacing the Palm Rest Assembly

5. Replace the keyboard (see

Replacing the Keyboard

6. Replace the LED cover (see

Replacing the LED Cover

7. Replace the display assembly (see

Replacing the Edge-to-Edge Display

Replacing the Display Assembly

8. Replace the secondary hard drive (see

Replacing the Secondary Hard Drive (HDD2)

9. Replace the base assembly cover (see

Replacing the Base Assembly Cover

10. Follow the procedures in

After Working on Your Computer

Back to Contents Page

Содержание Precision Workstation M6400


















































































Результаты поиска

Содержание Precision Workstation M6400

Отзывы:

Похожие инструкции для Precision Workstation M6400

Бренды по названию

Популярные бренды

Dell Precision Workstation M6400, Руководство по обслуживанию

Результаты поиска

Содержание Precision Workstation M6400

Отзывы:

Похожие инструкции для Precision Workstation M6400

Бренды по названию

Популярные бренды