Dell Latitude ST Скачать руководство пользователя

Страница: 8 / 65

Recommended Tools

The procedures in this document may require the following tools:

•

Small flat-blade screwdriver

•

#0 Phillips screwdriver

•

#1 Phillips screwdriver

•

Small plastic scribe

•

Flash BIOS update program CD

Turning Off Your Computer

CAUTION: To avoid losing data, save and close all open files and exit all open programs before you turn off your
computer.

Shut down the operating system.

Ensure that the computer and all attached devices are turned off. If your computer and attached devices did not

automatically turn off when you shut down your operating system, press and hold the power button for about 4

seconds to turn them off.

After Working Inside Your Computer

After you complete any replacement procedure, ensure you connect any external devices, cards, and cables before
turning on your computer.

CAUTION: To avoid damage to the computer, use only the battery designed for this particular Dell computer. Do not
use batteries designed for other Dell computers.

Содержание Latitude ST


































































Результаты поиска

Содержание Latitude ST

Отзывы:

Похожие инструкции для Latitude ST

Бренды по названию

Популярные бренды

Dell Latitude ST, Руководство пользователя

Результаты поиска

Содержание Latitude ST

Отзывы:

Похожие инструкции для Latitude ST

Бренды по названию

Популярные бренды