Dell Inspiron 9300 Скачать руководство пользователя

Страница: 1 / 60

Dell™ Inspiron™ 9300 Service Manual

Notes, Notices, and Cautions

Abbreviations and Acronyms

For a complete list of abbreviations and acronyms, see the

Dell Inspiron Help

file. To access the help file, click the

Start

button, click

Help and Support

, click

User and system guides

, click

User's guides

, and click

Dell Inspiron Help

If you purchased a Dell™ n Series computer, any references in this document to Microsoft®

Windows

operating systems are not applicable.

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Inc.

is strictly forbidden.

Trademarks used in this text:

Dell

, the

DELL

logo, and

Inspiron

are trademarks of Dell Inc.;

Microsoft

and

Windows

are registered trademarks of Microsoft Corporation;

Bluetooth

is a

registered trademark owned by Bluetooth SIG, Inc. and is used by Dell Inc. under license.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any
proprietary interest in trademarks and trade names other than its own.

Model PP14L

February 2005 Rev. A00

Before You Begin

Speakers

System Components

Subwoofer

Optical Drive

USB Port Board

Hard Drive

Microprocessor Thermal-Cooling Assembly

Memory Module

Microprocessor Module

Modem

Video Card/Thermal Cooling Assembly

Mini PCI Card

System Fans

Internal Card With Bluetooth

Wireless Technology

MCH Heat Sink

Hinge Cover

PC Card Cage

Keyboard

System Board

Display

Battery Latch Assembly

Palm Rest

Flashing the BIOS

Coin-Cell Battery

Pin Assignments for I/O Connectors

NOTE:

A NOTE indicates important information that helps you make better use of your computer.

NOTICE:

A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.

CAUTION:

A CAUTION indicates a potential for property damage, personal injury, or death.

Содержание Inspiron 9300





























































Результаты поиска

Содержание Inspiron 9300

Отзывы:

Похожие инструкции для Inspiron 9300

Бренды по названию

Популярные бренды

Dell Inspiron 9300, Руководство по обслуживанию

Результаты поиска

Содержание Inspiron 9300

Отзывы:

Похожие инструкции для Inspiron 9300

Бренды по названию

Популярные бренды