Dell Alienware M11x Скачать руководство пользователя

Страница: 29 / 39

Replacing the Mini-Card(s)

Follow the instructions in

Before You Begin

Remove the new Mini-Card from its packaging.

Insert the Mini-Card connector at a 45-degree angle into the connector on the system board.

Press the other end of the Mini-Card down into the slot on the system board and replace the screw that secures the Mini-Card to the system board.

Connect the appropriate antenna cables to the Mini-Card you are installing. The following table provides the antenna cable color scheme for each Mini-
Card supported by your computer.

Replace the battery pack (see

Replacing the Battery Pack

Replace the base cover (see

Replacing the Base Cover

Install the drivers and utilities for your computer, as required.

Back to Contents Page

CAUTION:

When the Mini-Card is not in the computer, store it in protective antistatic packaging. For more information, see "Protecting Against

Electrostatic Discharge" in the safety information that shipped with your computer.

CAUTION:

Use firm and even pressure to slide the card into place. If you use excessive force, you may damage the connector.

CAUTION:

The connectors are keyed to ensure correct insertion. If you feel resistance, check the connectors on the card and on the system

board, and realign the card.

Connectors on the Mini-Card

Antenna Cable Color Scheme

WWAN (2 antenna cables)

Main WWAN (white triangle)

Auxiliary WWAN (black triangle)

white with gray stripe

black with gray stripe

WLAN (2 antenna cables)

Main WLAN (white triangle)

Auxiliary WLAN (black triangle)

white

black

CAUTION:

Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer. Failure to do so may

result in damage to the computer.

NOTE:

If you are installing a communication card from a source other than Dell or Alienware, you must install the appropriate drivers and utilities.

Содержание Alienware M11x








































Результаты поиска

Содержание Alienware M11x

Отзывы:

Похожие инструкции для Alienware M11x

Бренды по названию

Популярные бренды

Dell Alienware M11x, Руководство по обслуживанию

Результаты поиска

Содержание Alienware M11x

Отзывы:

Похожие инструкции для Alienware M11x

Бренды по названию

Популярные бренды