Dell 3130cn - Color Laser Printer Скачать руководство пользователя страница 255 | Manualshive

Страница: 255 / 854

Dell 3130cn - Color Laser Printer Скачать руководство пользователя страница 255

1 - 229

Chapter 1 Troubleshooting

Version 1 2008.02.15

9

Checking the power to the DUP JAM SENSOR
Disconnect the connector of P/J430 on the PWBA DUP-H.
Is the voltage across ground <=> J430-1pin on the PWBA
DUP, about +3.3 VDC?

Go to step 10.

Go to step 11.

10

Checking the SENSOR PHOTO (DUP JAM SENSOR) for
operation
Disconnect the connector of P/J430 on the PWBA DUP-H.
Is the voltage across ground <=> J430-3pin on the PWBA
MCU
Does the voltage change, every time the actuator of the
DUP JAM SENSOR is operated?

Go to step 11.

Replace the

FEEDER ASSY

DUP. (Refer to

Removal 5/

Replacement 39.)

11

Checking the connectors of the PWBA DUP-H and PWBA
MCU for connection
Check the connections between the PWBA DUP-H and
PWBA MCU.
Are P/J428, P/J2720, P/J272 and P/J27 connected surely?

Go to step 12.

Reconnect the

connector(s)

P/J428, P/J2720,

P/J272 and/or

P/J27 surely.

12

Checking the HARNESS ASSY DUP UNIT for continuity
Disconnect P/J428 from the PWBA DUP-H.
Disconnect P/J2720 from the HARNESS ASSY FRONT
COVER.
Is each cable of P/J428 <=> P/J2720 continuous?

Go to step 13.

Replace the HAR-
NESS ASSY DUP

UNIT.

13

Checking the HARNESS ASSY FRONT COVER for conti-
nuity
Disconnect P/J2720 from the HARNESS ASSY DUP UNIT.
Disconnect P/J272 from the HARN ASSY R SIDE.
Is each cable of P/J2720 <=> P/J272 continuous?

Go to step 14.

Replace the HAR-

NESS ASSY

FRONT COVER.

14

Checking the HARN ASSY R SIDE for continuity
Disconnect P/J272 from the HARNESS ASSY FRONT
COVER.
Disconnect P/J27 from the PWBA MCU.
Is each cable of P/J272 <=> P/J27 continuous?

Go to step 15.

Replace the

HARN ASSY R

SIDE.

15

Checking the power to the PWBA DUP-H
Disconnect the connector of P/J27 on the PWBA MCU.
Is the voltage across ground <=> J27-17pin / J27-18pin on
the PWBA MCU, about +24 VDC?

Replace the

FEEDER ASSY

DUP

(Refer to Removal

5/ Replacement

39.)

Replace the

PWBA MCU.

(Refer to Removal

30/ Replacement

14.)

16

Checking the connectors of the PWBA DUP-H and
CLUTCH DUP for connection
Check the connections between the PWBA DUP-H and
CLUTCH DUP.
Are P/J431 connected surely?

Go to step 17.

Reconnect the

connector(s)

P/J431 surely.

17

Checking the power to the CLUTCH DUP
Disconnect the connector of P/J431 on the PWBA DUP.
Is the voltage across ground <=> J431-1pin on the PWBA
DUP, about +24 VDC?

Replace the

FEEDER ASSY

DUP

(Refer to Removal

5/ Replacement

39.)

Go to step 18.

Step

Check

Yes

No

«
...
253
254
255
256
257
...
»

Содержание 3130cn - Color Laser Printer























































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды