Dell 1600n - Multifunction Laser Printer B/W Скачать руководство пользователя страница 91

Страница: 91 / 189

Troubleshooting

Service Manual

7-1

7. Troubleshooting

7.1 Paper Feeding Problems

7.1.1 Wrong Print Position

• Description

Printing begins when the paper is in the wrong position.

Check and Cause

Solution

A defective feed sensor actuator can cause incorrect tim-
ing.

Replace the defective actuator

7.1.2 JAM 0

• Description

1. Paper has not exited from the cassette.
2. Jam-0 occurs if the paper feeds into the printer.

PTL

P IC

Empty Sensor

OPC

L S U

Fuser

Toner Cartridge

EXIT

Sensor

Feed

Sensor

MP Sensor

Check and Cause

Solution

1. Check the Solenoid by using Engine

Test Mode : Diagnostic Mode code 0

2. Check if the pad is loose due to bad

sealing of the side-pad.

3. Check the surface of the roller-pick-

up for foreign matter.

4. If continuous clusters occur, check

whether the assembly slot between
shaft-pickup and housing-pickup
become open or is broken away.

5. If the paper feeds into the printer

rand Jam 0 occurs, perform DCU to
check feed-sensor of the engine
board.

1. Replace the solenoid.

2. Replace the side-pad Assembly L or

R, if necessary.

3. Clean with soft cloth dampened with

IPA(Isopropyl Alcohol) or water.

4. Replace the Housing-Pickup and/or

Shaft-Pickup.

Содержание 1600n - Multifunction Laser Printer B/W






























































































































































































Результаты поиска

Содержание 1600n - Multifunction Laser Printer B/W

Отзывы:

Похожие инструкции для 1600n - Multifunction Laser Printer B/W

Бренды по названию

Популярные бренды

Dell 1600n - Multifunction Laser Printer B/W, Руководство по обслуживанию

Результаты поиска

Содержание 1600n - Multifunction Laser Printer B/W

Отзывы:

Похожие инструкции для 1600n - Multifunction Laser Printer B/W

Бренды по названию

Популярные бренды