Dell 1600n - Multifunction Laser Printer B/W Скачать руководство пользователя страница 103

Страница: 103 / 189

Troubleshooting

Service Manual

7-13

7.3.7 Uneven Density

• Description

Print density is uneven between left and right.

Check and Cause

Solution

1. The pressure force on the left and right

springs of the transfer roller is not even,
the springs are damaged, the transfer
roller is improperly installed, or the trans-
fer roller bushing or holder is damaged.

2. The life of the Developer has expired.

3. The toner level is not even on the devel-

oper roller due to the bad blade.

1. Replace both the left and right Spring

Holder.

2. Problem with the toner cartridge, replace

the toner cartridge and try to print out.

7.3.8 Background

• Description

Light dark background appears in whole area of the printing.

Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer

Check and Cause

Solution

1. Recycled recording paper has been

used.

2. The life of the Developer has expired.

3. The up-to-down movement of the trans-

fer roller is swift?

4. The HVPS is normal?

(Perform Engine Test Mode diagnostic
code 4)

1. Quality is not guaranteed when using recy-

cled paper.

2. Replace the toner cartridge.

3. Clean the busing on the transfer roller.

4. Replace the HVPS.

Содержание 1600n - Multifunction Laser Printer B/W






























































































































































































Результаты поиска

Содержание 1600n - Multifunction Laser Printer B/W

Отзывы:

Похожие инструкции для 1600n - Multifunction Laser Printer B/W

Бренды по названию

Популярные бренды

Dell 1600n - Multifunction Laser Printer B/W, Руководство по обслуживанию

Результаты поиска

Содержание 1600n - Multifunction Laser Printer B/W

Отзывы:

Похожие инструкции для 1600n - Multifunction Laser Printer B/W

Бренды по названию

Популярные бренды