Dell 10Gb Ethernet Pass Through II Скачать руководство пользователя страница 26

Страница: 26 / 26

Software User’s Manual

Rev 1.00

chassisaction –m switch-<n> powercycle

where <n> is the switch number [1-6].

5.3

Resolving a Link Protocol Mismatch

Log in to 10GbE PTM CLI and run the “show port link” command. Check the status of the down-
link and uplink in the relevant port to identify the mismatch – see

Section 3.7.1

for details.

5.4

Resolving CLI Connectivity Problems

Reboot the 10GbE PTM through the CMC CLI using the following command:

chassisaction –m switch-<n> powercycle

where <n> is the switch number [1-6].

5.5

Recovery From Non-Responsive 10GbE PTM CLI

Reboot the 10GbE PTM through the CMC CLI using the following command:

chassisaction –m switch-<n> powercycle

where <n> is the switch number [1-6].

5.6

Recovery From a Software Update Failure

1. Reboot the 10GbE PTM through the CMC CLI using the following command:

chassisaction –m switch-<n> powercycle

where <n> is the switch number [1-6].

2. Restart the software update process.

Содержание 10Gb Ethernet Pass Through II



























Результаты поиска

Содержание 10Gb Ethernet Pass Through II

Отзывы:

Похожие инструкции для 10Gb Ethernet Pass Through II

Бренды по названию

Популярные бренды

Dell 10Gb Ethernet Pass Through II, Руководство пользователя

Результаты поиска

Содержание 10Gb Ethernet Pass Through II

Отзывы:

Похожие инструкции для 10Gb Ethernet Pass Through II

Бренды по названию

Популярные бренды