Dell EMC VxRail E series Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 54

background image

10

Dell EMC VxRail Multirack Deployment Guide

The Dell EMC Networking S5248F-ON is a 1-RU fixed switch with 48x 25 GbE, 4x multirate 100 GbE, and 2x
200 GbE ports, and supports L2 static VXLAN with VLT. The example within this document uses four
S5248F-ON switches in VLT pairs, as leaf switches.

Dell EMC Networking S5248F-ON

2.3

Dell EMC Networking Z9264F-ON

The Dell EMC Networking Z9264F-ON is a 2-RU 100 GbE aggregation/spine switch with up to 64 ports of
multirate 100 GbE, or up to 128 ports of 10/25/40/50 GbE ports, using supported breakout cables. The switch
is a scalable L2 and L3 Ethernet switch with QoS and a full complement of standards-based IPv4 and IPv6
features, including OSPF and BGP routing support. The example within this document uses two Z9264F-ON
switches as spine switches.

Dell EMC Networking Z9264F-ON

2.4

Dell EMC Networking S3048-ON

The Dell EMC Networking S3048-ON is a 1-RU switch with 48x1GbE BASE-T ports and 4x 10GbE SFP+
ports. This guide uses one S3048-ON switch for out-of-band (OOB) management traffic.

Dell EMC Networking S3048-ON

«
...
8
9
10
11
12
...
»

Содержание VxRail E series























































Отзывы:

Нет отзывов

Похожие инструкции для VxRail E series

Бренд: ZETR Страницы: 2

Бренд: CallDirect Страницы: 33

BB-HGW700A - Network Camera Router

Бренд: Panasonic Страницы: 10

Бренд: Accuphase Страницы: 2

Бренд: ADTRAN Страницы: 2

AMB-VDX3H1 Series

Бренд: Acrosser Technology Страницы: 4

Бренд: Javad Страницы: 35

PARTNER Voice Messaging PC Card Release 2

Бренд: Lucent Technologies Страницы: 67

eXtremeRAID 1100

Бренд: Mylex Страницы: 74

AT-9424Ts/XP AC

Бренд: Allied Telesis Страницы: 3

LoadMaster 1500

Бренд: KEMP Technologies Страницы: 71

Бренд: protech Страницы: 95

Бренд: Kontron Страницы: 42

Бренд: Kramer Страницы: 2

Бренд: iGateWeb.com Страницы: 6

Бренд: Axis Страницы: 98

Бренд: ZyXEL Communications Страницы: 3

DEEP LEARNING PLUS

Бренд: Concept Pro Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды