Dell EMC ES40 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 66

background image

l

Before touching any unit, touch a bare (unpainted) metal surface of the cabinet/rack or
enclosure.

l

Before removing any unit from its antistatic bag, place one hand firmly on a bare metal surface
of the cabinet/rack or enclosure, and at the same time, pick up the unit while it is still sealed in
the antistatic bag. At the same time, do not move around the room or touch other furnishings,
personnel, or surfaces until you have installed the unit.

l

When you remove a unit from the antistatic bag, avoid touching any electronic components
and circuits on it.

l

If you must move around the room or touch other surfaces before installing a unit, first place
the unit back in the antistatic bag. When you are ready again to install the unit, repeat these
procedures.

Hardware acclimation times

Units must acclimate to the operating environment before applying power. This requires the
unpackaged system or component to reside in the operating environment for up to 16 hours in
order to thermally stabilize and prevent condensation.

Transit/storage environment

Operating environment
temperature

Acclimation time

Temperature

Humidity

Nominal

68-72°F
(20-22°C)

Nominal

40-55% RH

Nominal 68-72°F (20-22°C)

40-55% RH

0-1 hour

Cold

<68°F (20°C)

Dry

<30% RH

<86°F (30°C)

4 hours

Cold

<68°F (20°C)

Damp

≥30% RH

<86°F (30°C)

4 hours

Hot

>72°F (22°C)

Dry

<30% RH

<86°F (30°C)

4 hours

Hot

>72°F (22°C)

Humid
30-45% RH

<86°F (30°C)

4 hours

Humid
45-60% RH

<86°F (30°C)

8 hours

Humid
≥60% RH

<86°F (30°C)

16 hours

Unknown

<86°F (30°C)

16 hours

l

If there are signs of condensation after the recommended acclimation time has passed, allow
an additional eight (8) hours to stabilize.

l

Systems and components must not experience changes in temperature and humidity that are
likely to cause condensation to form on or in that system or component. Do not exceed the
shipping and storage temperature gradient of 45°F/hr (25°C/hr).

Removing and replacing FRUs

Dell EMC ES40 Expansion Shelf Guide Field Replacement Unit Guide

15

«
...
13
14
15
16
17
...
»

Содержание ES40



































































Отзывы:

Нет отзывов

Похожие инструкции для ES40

Бренд: Naterial Страницы: 16

Бренд: W.Schillig Страницы: 13

Бренд: HABYS Страницы: 9

Бренд: HABYS Страницы: 12

Бренд: Zaor Страницы: 6

Бренд: OAKWORKS Страницы: 4

Бренд: K&B Furniture Страницы: 4

Бренд: Gami Страницы: 4

Бренд: Habitat Страницы: 6

Бренд: Habitat Страницы: 7

Бренд: Habitat Страницы: 12

Бренд: Habitat Страницы: 6

Бренд: Habitat Страницы: 7

Бренд: Habitat Страницы: 11

Бренд: Habitat Страницы: 6

Бренд: Habitat Страницы: 9

Бренд: HABYS Страницы: 8

Бренд: Watson Desking Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды