Dell EMC E68S Скачать руководство пользователя страница 57

Страница: 57 / 187

Steps

1. Press the blue release tabs to disengage the drive backplane from the hooks on the system.
2. Lift and pull the drive backplane out of the system.

NOTE:

To avoid damaging the backplane, ensure that you move the control panel cables from the cable routing clips

before removing the backplane.

Figure 51. Removing the drive backplane

Next steps

Replace the drive backplane

Installing the drive backplane

Prerequisites

1. Follow the safety guidelines listed in the

Safety instructions

on page 26.

2. Follow the procedure listed in the

Before working inside your system

on page 27.

Remove the backplane cover

4. If installed,

remove the air shroud

Remove all the drives

Remove the cooling fan cage assembly

NOTE:

To avoid damaging the backplane, ensure to move the control panel cables from the cable routing clips before

removing the backplane.

NOTE:

Route the cable properly when you replace it to prevent the cable from being pinched or crimped.

Steps

1. Use the guides on the system as guides to align the slots on the backplane.

Installing and removing system components

Содержание E68S




























































































































































































Результаты поиска

Содержание E68S

Отзывы:

Похожие инструкции для E68S

Бренды по названию

Популярные бренды

Dell EMC E68S, Инструкция по установке и обслуживанию

Результаты поиска

Содержание E68S

Отзывы:

Похожие инструкции для E68S

Бренды по названию

Популярные бренды