Degelman PILEDRIVER Скачать руководство пользователя

Страница: 28 / 30

-24-

143558 - PileDriver (26-June-2012)

Mounting

10 STEP MOUNTING

PROCEDURE

Procedure to mount blade:

1. Align the tractor behind the main frame.
2. Jack up the pivot frame high enough so the main

frame hook is just below the side bracket pin.

3. Open the D-locks and remove handle.
4. Drive forward until the pin is just behind the

hook.

5. Hook up the hydraulics.
6. Extend the lift cylinders until the hooks are lifted

up level with the side bracket pins.

7. Drive forward to engage the side bracket pins.
8. Retract the lift cylinder bringing the D-lock

connection points up to the axle bracket pins.

(By retracting the lift cylinder, the weight of

the front of the blade swings the back frame

upward, engaging the axle bracket pins.)

9. Close the D-lock connections using the handle.

Install the D-lock clip pins and store the handle.

10. Remove frame jacks and place in their storage

positions.

Important:

You must retract lift cylinders to lift

blade before unlatching D-lock! This transfers the
weight to the front hooks and frees up the D-lock.
Otherwise, the whole assembly may come crashing
down.

Procedure to remove blade:

  1.  Retract lift cylinder to lift blade.
  2.  Open D-lock latches.
  3.  Lower blade by extending the lift cylinders

    - main frame will disengage from brackets.
  4.  If applicable, use frame support jacks.
  5.  Check that connection points are

disconnected and clear to back out.

6. Unhook hydraulics.
7. Back tractor out.

DANGER

UNHOOKING - REMOVING BLADE

Axle

Bracket Pin

Side

Bracket Pin

Side

Bracket Pin

Side

Bracket Pin

Jack

Mounting

STEP

Hook

Pivot Frame

Dlock

Hook

Hydraulics

Lift

Cylinder

Level

Axle

Bracket Pin

Side

Bracket Pin

Axle

Bracket Pin

3/8 - 1/2 gap

Side

Bracket Pin

Hook

Important:

There

should be a small gap

(3/8”-1/2”) between the

inside of the hook to the

front of the bracket pin.

Please note:

The brackets & frame

assembly for your

particular fit-up may

differ significantly from those used in the diagram, however,

the basic mounting procedure should remain the same. (Refer

to the “10 STEP MOUNTING” procedure and diagram below)

Содержание PILEDRIVER































Результаты поиска

Содержание PILEDRIVER

Отзывы:

Похожие инструкции для PILEDRIVER

Бренды по названию

Популярные бренды

Degelman PILEDRIVER, Руководство оператора / Каталог запасных частей

Результаты поиска

Содержание PILEDRIVER

Отзывы:

Похожие инструкции для PILEDRIVER

Бренды по названию

Популярные бренды