Degelman PILEDRIVER Скачать руководство пользователя

Страница: 23 / 30

-19-

143558 - PileDriver (26-June-2012)

Brackets Installation

Note C:

Install Degelman axle bracket

with the 4 bolts removed from

top axle (M24 X 150) along

with 2 Degelman bolts and new

M24 flat and lock washers.

Axle Bracket

Side

Bracket

Lift Hole

Note A:

If equipped, remove

JD tractor bracket

from under axle.

Note D:

Install with new bolts (13

- M24 x 180) and existing

flat washers from note B.

Shim if there is a gap.

Stack shims as required.

Tighten.

Tractor Frame

(top view)

Note B:

Remove the four

(per side) top inner

bolts holding the frame

to the axle.
Retain the flat washers.
Leave the tractor’s

two outer bolts in place.

• Remove tractor’s step

• Open hood & side doors

• Remove JD axle bracket (see note A below)

• Remove top 4 inner axle bolts (see note B below)

• Install Degelman axle bracket (see note C below)

• Suspend side bracket

• Lower into place

• Loosely install: 1 - Bolt, 7/8 x 4

2 - Bolt, 7/8 x 3

3 - Bolt, 3/4 x 3

(and required hardware)

• Install and tighten:
- to tractor axle. (see note D below)
- to tractor frame. (items 2, 3, and hardware)
- to axle bracket. (items 1 & hardware)

• Drill and install hardware. (see note E below)

IMPORTANT-TORQUE

Torque all bolts properly!

Refer to maintenance

section for torque

specifications.

BRACKET INSTALLATION

118503 - Lock Washer, M8 (3)

790860 - Hydraulic

Coupler Bracket (1)

118128 - Bolt, M8 x 40 P8.8 (3)

Invert the shield

& re-install upside

down

Note E:

Drill 13/16 hole in tractor frame,

install and tighten hardware.

Panel

•Remove the front bolts holding the panel under the frame.

•Install the hyd coupler mount using the new M8 x 40

bolts & hardware.

Shim

M24 x 150

M24 x 180

Содержание PILEDRIVER































Результаты поиска

Содержание PILEDRIVER

Отзывы:

Похожие инструкции для PILEDRIVER

Бренды по названию

Популярные бренды

Degelman PILEDRIVER, Руководство оператора / Каталог запасных частей

Результаты поиска

Содержание PILEDRIVER

Отзывы:

Похожие инструкции для PILEDRIVER

Бренды по названию

Популярные бренды