background image

Dedicated Micros ©2007

Domes

Important Safeguards

Product Safety

WARNING

• 

Installation and servicing is only to be carried out by suitably qualified and 

experienced personnel.

• 

Do not remove covers as there is a risk of injury or death by electric shock.

• 

Only power low voltage dome cameras from a class 2 isolated power supply.

This camera range is designed for use in general purpose CCTV applications and has no other 

purpose.
Only operate your camera between the temperatures of -10°C and +50°C. Do not operate your 

camera outside its specified power supply range.

Electromagnetic Compatability (EMC)

CAUTION

This product is intended solely for use in general CCTV applications.
The product must be installed and maintained in accordance with good installation practice to enable 

the product to function as intended and to prevent problems. Refer to your agent for installation 

guidance.

Declaration of Conformity

The manufacturer declares that the equipment supplied with this manual is compliant with the 

essential protection requirements of the EMC directive 89/336 and the Low Voltage Directive LVD 

73/23 EEC.
Conforming to the requirements of standards EN55022 for emissions, EN61000-4 parts 2, 3, 4, 5, 6 

and 11 for immunity and EN60950 for Electrical Equipment safety.

FCC CLASS B REGULATORY NOTICE

This device complies with part 15 of the FCC Rules. Operation is subject to the following two 

conditions: (1) This device may not cause harmful interference, and (2) this device must accept any 

interference received, including interference that may cause undesired This equipment has been 

tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC 

Rules. These limits are designed to provide reasonable protection against harmful interference in 

a residential installation. This equipment generates uses and can radiate radio frequency energy 

and, if not installed and used in accordance with the instructions, may cause harmful interference to 

radio communications. However, there is no guarantee that interference will not occur in a particular 

installation. If this equipment does cause harmful interference to radio or television reception, which 

can be determined by turning the equipment off and on, the user is encouraged to try to correct the 

interference by one or more of the following measures:
 

Reorient or relocate the receiving antenna.

 

Increase the separation between the equipment and receiver.

 

Connect the equipment into an outlet on a different circuit different to the receiver.

 

Consult the dealer or an experienced radio/TV technician for help.

 

Modifications not expressly approved by the manufacturer could void the user’s authority to 

 

 

operate the equipment under FCC rules.

Содержание ICE series

















Отзывы: