DCB SPL Multidrop Скачать руководство пользователя страница 14

Страница: 14 / 30

5.4

Commands

5.4.1

Help (H or ?)

COMMAND

LOCAL REMOTE PARAGRAPH

Help:

Network

5.4.2

Port

5.4.3

Show: Port Config

5.4.4

5.4.8

Map

5.4.10

Status

5.4.11

Network Config

5.4.12

Change: Port Config

RCP

5.4.5 & 6

Delay Timeout

5.4.7

5.4.9

Network Config

5.4.13

Activity Counts

5.4.14

Drop Activity

5.4.15

Zero Activity Counters

5.4.14

Flow Control

5.4.16

Test Tools

5.4.20

Type

RTY

5.4.17

Repeat Last Command

5.4.18

Disconnect NMP

BYE

5.4.19

5.4.2

Help Network

The Help Network (HN) command displays the drop address settings

for the 6-position drop address switch.

5.4.3

Help Port

The Help Port (HP) command displays switch settings for the 8-

position port configuration switches.

5.4.4

Show Port Config

The Show Port Config (SC) command shows the current port

configuration settings for both the local and the remote ports. Port

numbers may be included with this command to limit the display

range. If no port numbers are included, settings for all ports are shown.

Use this command to verify proper port configuration.

Содержание SPL Multidrop































Результаты поиска

Содержание SPL Multidrop

Отзывы:

Похожие инструкции для SPL Multidrop

Бренды по названию

Популярные бренды

DCB SPL Multidrop, Руководство пользователя

Результаты поиска

Содержание SPL Multidrop

Отзывы:

Похожие инструкции для SPL Multidrop

Бренды по названию

Популярные бренды