DAVIS Wireless Repeater 7614 Скачать руководство пользователя страница 16

Product Numbers: 7614 & 7615

Davis Instruments Part Number: 7395-105
Wireless Repeater with Solar or AC-Power
Rev. A Manual (7/8/99)
Controlled Online:  Weather Manuals:Accessories:Wireless Repeater
This product complies with the essential protection requirements of the EC EMC Directive 89/336/EC. 
© 1999  Davis Instruments Corp. All rights reserved.

3465 Diablo Avenue, Hayward, CA 94545-2778

510-732-9229 • Fax: 510-732-9118

E-mail: [email protected]  •  www.davisnet.com

S

PECIFICATIONS

Transmit frequency: 916.5 MHz

ID codes: 8 user-selectable

License: Low power (less than 1 mW), no license required

Temperature range: -40 to 60 °C

Power Input: 4 to 12 VDC output @ 1.5 mA

FCC P

ART

 15 C

LASS

 B R

EGISTRATION

 W

ARNING

This equipment has been tested and found to comply with the limits for a class 
B digital device, pursuant to Part 15 of the FCC Rules.  These limits are 
designed to provide reasonable protection against harmful interference in a 
residential installation.  This equipment generates, uses and can radiate radio 
frequency energy and, if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio communications.  However, 
there is no guarantee that interference will not occur in a particular installa-
tion.  

If this equipment does cause harmful interference to radio or television recep-
tion, which can be determined by turning the equipment off and on, the user is 
encouraged to try to correct the interference by one or more of the following 
measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the 
receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Shielded cables and I/O cords must be used for this equipment to comply 
with the relevant FCC regulations.  Changes or modifications not expressly 
approved in writing by Davis Instruments may void the user's authority to 
operate this equipment.

Содержание Wireless Repeater 7614

















Отзывы: