manualshive.com logo in svg
background image

24

 

 

If the pump does not operate, the following conditions may apply:

 

1. The  power  is  not  connected.  For  240  volts  only,  check  the  power  point  by 

plugging in a portable appliance to ensure power is available. Also check fuses 
and the main power supply switch

 

2. Automatic overload is tripped. The pump has an in-built thermal overload which 

will  reset  automatically  after  the  motor  has  cooled  following  an  overheating 
period. Determine the cause of the overload tripping and rectify. Reset the pump 
by switching the power OFF for 30 seconds.

 

3. Blockage is preventing the pump from rotating.

 

 

 

Removal of the Pump from Pipework

 

Should it be necessary to remove the pump, follow these instructions:

 

1. Switch off the power and remove the plug from the power source.

 

 

NOTE: If the pump is wired into a time clock or another automatic 

control, the wiring should be removed by a qualified technician.

 

2. Close the water valves on the pool return and the pump inlet pipework.

 

3. Remove the discharge & suction barrel unions taking care not to lose the o-

rings.

 

4. Move the pipework with the barrel unions attached until the pump can be pulled 

clear.

 

 

NOTE: When making any enquiries about your SilensorPro, be certain 

to quote the model number from the nameplate located on the motor.

 

 

 

Water Quality

 

Maintaining balanced water chemistry is important to the life of your pool pump. 
This  pump  is  designed  to  be  used  with  Pool  &  Spa  water,  balanced  in 
accordance with Langelier Saturation Index, with a pH level of between 7.2 and 
7.6 and is regularly treated with a chlorine sanitising agent with the level not 
exceeding 3.0 ppm.

 

Please consult your local pool shop regularly to have your water tested. 

 

 

 
 
 
 
 

 

Содержание SILENSOR PRO SP200BTP

























Отзывы: